Truckers Report Jobs

Find Trucking Jobs

Company Driver Company Driver Dry Van Dry Van Flatbed Flatbed Refrigerated Refrigerated Specialized Specialized Owner Operator Owner Operator
More Trucking Job Searches ⌄ Fewer Trucking Job Searches
⌃

my truck has a code for engine stop occurance its a kenworth with cat engine

Discussion in 'Kenworth Forum' started by Alberta-Mechanic, Aug 19, 2014.

  1. Aug 19, 2014 #1
    Alberta-Mechanic

    Alberta-Mechanic Light Load Member

    66
    19
    Aug 19, 2014
    Grande prairie Alberta Canada
    0
    quick stop occrance code help what do I do
     
    Alberta-Mechanic, Aug 19, 2014
    Alberta-Mechanic, Aug 19, 2014
    #1
  2. Truckers Report Jobs

    Trucking Jobs in 30 seconds

    Every month 400 people find a job with the help of TruckersReport.

  3. Aug 19, 2014 #2
    j_martell

    j_martell Light Load Member

    284
    184
    Jun 12, 2014
    Centre Wellington, Ontario
    0
    Fix it. Coolant level/oil pressure would trip a shutdown.....I would hope you checked that at minimum....
     
    j_martell, Aug 19, 2014
    j_martell, Aug 19, 2014
    #2
  4. Aug 19, 2014 #3
    kwcam

    kwcam Light Load Member

    193
    145
    Dec 29, 2012
    at the shop
    0
    With Cat ET set the parameter to 0 will turn it off. most come from factory set a 4 mph, we turn them up to 9 or 10 when the customer asks for it to be left on.
     
    kwcam, Aug 19, 2014
    kwcam, Aug 19, 2014
    #3
    Alberta-Mechanic Thanks this.
  5. Aug 20, 2014 #4
    Alberta-Mechanic

    Alberta-Mechanic Light Load Member

    66
    19
    Aug 19, 2014
    Grande prairie Alberta Canada
    0
    Of course I checked levels. I can't get code to go away it stays active. Quick stop occurrence code 84
     
    Alberta-Mechanic, Aug 20, 2014
    Alberta-Mechanic, Aug 20, 2014
    #4
  7. Aug 20, 2014 #5
    Alberta-Mechanic

    Alberta-Mechanic Light Load Member

    66
    19
    Aug 19, 2014
    Grande prairie Alberta Canada
    0
    Sorry it comes on active when key is turned than gos inactive again the driver has complained about coolant temp not Geting warm I think that is unrelated changing thermostats tomorrow I'm thinking they are stuck open. I'm wondering for the quick stop occurance code if it is in the 5volt sensor supply circuit there might be a problem he has also complained about Gage's fluctuating and jumping. I'm not sure what your saying to about setting paramator wich one?
     
    Alberta-Mechanic, Aug 20, 2014
    Alberta-Mechanic, Aug 20, 2014
    #5
  8. Aug 20, 2014 #6
    kwcam

    kwcam Light Load Member

    193
    145
    Dec 29, 2012
    at the shop
    0
    Quick stop is a recorder of a few parameters such as cruise control, speed, brake application etc, so if the truck does a sudden stop it will record all these parameters, DOT likes to look at this if in an accident.
    In configurations, open all groups and scroll down it is probably set to look of trip speed, usually at 4 mph from factory, you can turn it off by setting it to 0 (zero) or set it to the max which is 10 or 12 mph.
    this does not cause any driving issues, the code just lets you know that these conditions have been met.
    you may want to check your trans out put nut, make sure its tight as it holds the speed tone wheel, if loose the tone wheel will send bad signal to ecm.
     
    kwcam, Aug 20, 2014
    kwcam, Aug 20, 2014
    #6
  9. Aug 21, 2014 #7
    Alberta-Mechanic

    Alberta-Mechanic Light Load Member

    66
    19
    Aug 19, 2014
    Grande prairie Alberta Canada
    0
    Ok man tomorrow first thing I'll get on that thanks bud unfortunately I'm also having trouble with my scan tool it's a Nexique not sure rite now the name but any way I can't seem to get files loaded in it so I can change parameters. And my laptop only has cummins INSITE on it. But I will try all your suggestions tomorrow appreciate the help now if only you can tell me every thing I need to know about abox install in a truck that's never had one I got another thread on here for that one. Lol
     
    Alberta-Mechanic, Aug 21, 2014
    Alberta-Mechanic, Aug 21, 2014
    #7
  10. Aug 24, 2014 #8
    Alberta-Mechanic

    Alberta-Mechanic Light Load Member

    66
    19
    Aug 19, 2014
    Grande prairie Alberta Canada
    0
    Darn my hand held scanner won't change that it is set at 25km/h on low side any way I will buy rite computer program for my lap top and try yoke but and speed sensor look good
     
    Alberta-Mechanic, Aug 24, 2014
    Alberta-Mechanic, Aug 24, 2014
    #8
  • Truckers Report Jobs

    Trucking Jobs in 30 seconds

    Every month 400 people find a job with the help of TruckersReport.