In Michigan you can get cited for having the tandems to far forward also. Just remember Tandems moving forward is lighter on Drives and heavier on the Tandems. and just the opposite when moving them to the back. My trailers are marked for the 41 foot mark, and I know that in Calif. they can't be no further back than 1 foot in front of that mark. New York would be 1 foot further back than where Calif allows for them to be, just like Michigan.
BRIDGE LAWS , Tandem holes HELP!!!
Discussion in 'Questions From New Drivers' started by OutboundGateChic, Jul 28, 2012.
Page 3 of 11
-
-
Trucking Jobs in 30 seconds
Every month 400 people find a job with the help of TruckersReport.
-
CAXPT Thanks this.
-
The driver I was speaking of could have adjusted his 5th wheel. And I hear all the time it's stuck because it had never been moved. I only mention what the drivers state. The domestic containers are scaled prior to being drayed from our DC to the RR and must meet california bridge law as that is where they are going. We have a few carriers that use 48' trailers and 53' rail boxes. In my steamship line days i had boxes transloaded on to step decks, low boys and aslo had over weight 40's in CA flipped on to super chassis if we could find them available. Which was only to move them to a facility that could perform a partial transload. Because shippers overseas apparently could care less how heavy they load ocean boxes.
I did not know that 48' or under can have tandems anywhere.Everett Thanks this. -
Thanks wiseguy, the driver earlier this morning had it in the 19th hole...
-
we go to oakland & newark with reefer containers on spread axle chasis's; thank goodness that's one thing we dont have to worry about when we do those
-
so, the 53 flats and steps would actually be legal. as those are spreads and i THINK most are non moveable.
i think i've heard of one trailer that could actually slide the back axle. and one trailer that could actually slide both axles. but the rest i've seen are pretty much stationary. -
Ms Gate lady. It is not your job to teach a driver his job. thnx for being nice, BUT, the placement of axles and weighing of trailers is the drivers job. Even if there were no scales at your place, we , as drivers are required to get it correct at the closest public scale possible.
placing the wheels in the legal position doesn't magically make the weight even. your warehouse people should know how to load it so it can weight out legal.
I repeat it is not your job !! save yourself the headaches and just make copies of atlas page and hand it out, if you must do something.
if they don't understand the job ,they need to talk to their company, not you.
thnx again for trying to help the clueless "steering wheel holders" out there. they to learn their job.jbatmick, Wingnut1, Everett and 1 other person Thank this. -
Good attitude. But this will also benefit you as well. You'll be better at your job not just by assisting, but by knowing all the facets of your job, and then some. I applaud you for taking the initiative.
Everett and Powder Joints Thank this. -
You really should refrain from coaching the drivers as your maybe opening yourself up to liability. It is every drivers job to know how to adjust the tandems. As far as the fith wheel being slid, some are fixed and some are adjustable, but if it is set correctly it would be a very rare occasion to need to adjust it. That is unless your grossed out and loaded really heavy in the front. I have on very rare occasions needed to adjust the fifth wheel, but very rare. Usally after someone who did not know what they were doing moved it.
My tractor now and for the last 10 years have had fixed placement on the fifth wheel and it has never been an issue. I change between powder, liquid tank, vans and flats. I simply put the load where I need the weight to be to start with. -
Trucking Jobs in 30 seconds
Every month 400 people find a job with the help of TruckersReport.
Page 3 of 11