Truckers Report Jobs

Find Trucking Jobs

Company Driver Company Driver Dry Van Dry Van Flatbed Flatbed Refrigerated Refrigerated Specialized Specialized Owner Operator Owner Operator
More Trucking Job Searches ⌄ Fewer Trucking Job Searches
⌃

Where is my speed sensor located?

Discussion in 'Kenworth Forum' started by Misterpreston, Oct 20, 2016.

  1. Oct 20, 2016 #1
    Misterpreston

    Misterpreston Light Load Member

    96
    4
    Mar 24, 2016
    0
    I have a 2012 T700 with a paccar MX13 engine. I have a omnitronics installed and it hasn't been recording my mileage. So I had the system looked at and apparently the system is fine so they tell me it could be my speed sensor. Before this mp50 or whatever it is I was leased on with another company who had peoplenet and I had no problems. So I'm going to buy the speed sensor and replace it myself just need to know the location.
     
    Misterpreston, Oct 20, 2016
    Misterpreston, Oct 20, 2016
    #1
  2. Truckers Report Jobs

    Trucking Jobs in 30 seconds

    Every month 400 people find a job with the help of TruckersReport.

  3. Oct 20, 2016 #2
    supersnackbar

    supersnackbar Road Train Member

    17,018
    38,422
    Aug 19, 2007
    Your Town, USA
    0
    It should be on the tailshaft of the transmission.
     
    supersnackbar, Oct 20, 2016
    supersnackbar, Oct 20, 2016
    #2
  4. Oct 21, 2016 #3
    nasriza

    nasriza Road Train Member

    2,368
    2,040
    Feb 1, 2013
    Chicago, IL
    0
    if your speedometer is showing than you shouldn't have any issues with what the mp50 is reading. i think they should check to make sure they gave the proper adapter for that as it shows a 9 pin buy i believe it reads OBD
     
    nasriza, Oct 21, 2016
    nasriza, Oct 21, 2016
    #3
  5. Oct 21, 2016 #4
    Misterpreston

    Misterpreston Light Load Member

    96
    4
    Mar 24, 2016
    0
    Yea my speedometer reads fine no issues there. I don't know what else it could be other than the ecm.
     
    Misterpreston, Oct 21, 2016
    Misterpreston, Oct 21, 2016
    #4
  7. Nov 4, 2016 #5
    WitchingHour

    WitchingHour Road Train Member

    3,422
    2,142
    Apr 1, 2011
    Broomfield, CO
    0
    Pretty sure Omnitracs is J1708.
     
    WitchingHour, Nov 4, 2016
    WitchingHour, Nov 4, 2016
    #5
  8. Nov 4, 2016 #6
    Antinomian

    Antinomian Road Train Member

    1,936
    2,936
    Feb 17, 2013
    0
    I had a similar problem with a Qualcomm once. It wouldn't automatically switch to drive status when the truck was moving, and it wouldn't record mileage traveled. It turned out to be a bad MASS unit. The MASS is a component of the QC system, not part of the truck.
     
    Antinomian, Nov 4, 2016
    Antinomian, Nov 4, 2016
    #6
  • Truckers Report Jobs

    Trucking Jobs in 30 seconds

    Every month 400 people find a job with the help of TruckersReport.