Trucking Jobs New Driver Jobs Flatbed Jobs Tanker Jobs Refrigerated Jobs Auto Hauler Jobs
Page 1 of 3 123 LastLast
Results 1 to 10 of 22

Thread: icon sucks!

  1. #1
    Bobtail Member
    Member Since
    Oct 2010
    Location
    nashville tn
    Trucker?
    25 Years
    Posts
    6
    Thanks
    0
    Thanked: 0 Times

    icon sucks!

    I have a 06 int. that is an old usa truck with a cummins isx motor and the icon idle control on it. The icon dont work and I have taken to the cummins dealer 2 times now to turn the icon thing off. It will idle for about 5 min then icon light will flash and shut down even after seting temp and everything. Cummins said they cant get computer to comunicate with the icon thing and didnt even know where it was on truck! I found it under pass side kick panel just would like to know how to bypass wiring on it. Cummins changes idle time on ecm trying to get it to idel so if i can bypass it it should be ok. Anyone got some expertese on this?


  2. #2
    Road Train Member Pablo-UA's Avatar
    Member Since
    Oct 2010
    Location
    Borispol, Ukraine
    Trucker?
    Trucking Industry
    Posts
    6,589
    Thanks
    24
    Thanked: 1,152 Times
    it is not so difficult. you need Cummins Insite 6 ore higher to disable icon ore change parameters, like delay!

    Can you see Icon control unit (in sleeper may be). It is a box with buttons like a DD OptiIdle... you can program it for longer idle time ore oil temp. control

    If Icon control panel is bad, just disable idle shutdown with Insite

  3. #3
    Medium Load Member
    Member Since
    Feb 2010
    Location
    Arkansas
    Trucker?
    EX-5 Years
    Posts
    513
    Thanks
    24
    Thanked: 134 Times
    or, if it is a usa truck, pull glove box out, look/feel behind the fuse panel. there should be a plastic block with 2 fuses in it, pull 1 and if the truck does not start, then put it back in and pull the other 1 out, that is the fuse for the icon. take it out and it will idle anytime. Now sometimes that block is ziptied way down behind the fuse panel, sometimes its just loose. hope you can find it.

  4. #4
    Road Train Member Pablo-UA's Avatar
    Member Since
    Oct 2010
    Location
    Borispol, Ukraine
    Trucker?
    Trucking Industry
    Posts
    6,589
    Thanks
    24
    Thanked: 1,152 Times
    wire from ign. switch runs to ICON and ICON starts the engine. if you pull out ICON you need to jump start wires.

  5. #5
    Bobtail Member
    Member Since
    Oct 2010
    Location
    nashville tn
    Trucker?
    25 Years
    Posts
    6
    Thanks
    0
    Thanked: 0 Times
    Thanks for the replies, i will look for the fuses behind the panel monday when i go in. I found one wire off icon box that said ecm feed and was going to jump straight from fuse to it. I pulled fuse marked icon ecm and that stoped the icon light from coming on when you turn key on so i figugerd it would stop it if i can just get jucie to ecm! Thanks a lot for the help hands!

  6. #6
    Medium Load Member
    Member Since
    Feb 2010
    Location
    Arkansas
    Trucker?
    EX-5 Years
    Posts
    513
    Thanks
    24
    Thanked: 134 Times
    I work in the shop at usa, so what I tell you about the 2 fuse block behind the fuse panel is correct for about 90% of the 9400's we had. if u pull 1 and the truck doesnt start, put it back in and pull the other 1. once you find it!

  7. #7
    Bobtail Member
    Member Since
    Oct 2010
    Location
    nashville tn
    Trucker?
    25 Years
    Posts
    6
    Thanks
    0
    Thanked: 0 Times
    Ok thanks a lot had to go to a funeral today so i didnt get to mess with the truck. I look 1 st thing monday morning when i go in, and thank you to everyone for the help!

  8. #8
    Bobtail Member
    Member Since
    Nov 2010
    Location
    salisbury,nc
    Trucker?
    18 Years
    Posts
    3
    Thanks
    1
    Thanked: 0 Times

    cummins icon

    there is no way to by pass it i tryed everything i could to by pass the one i have in my volvo.im taking the truck to volvo to have them remove it all together its the only way.

  9. #9
    Medium Load Member
    Member Since
    Feb 2010
    Location
    Arkansas
    Trucker?
    EX-5 Years
    Posts
    513
    Thanks
    24
    Thanked: 134 Times
    may not be on a volvo but his int9400 I know you can bypass it, because some that we sell they want it unhooked.

  10. #10
    Road Train Member Pablo-UA's Avatar
    Member Since
    Oct 2010
    Location
    Borispol, Ukraine
    Trucker?
    Trucking Industry
    Posts
    6,589
    Thanks
    24
    Thanked: 1,152 Times
    Quote Originally Posted by myers trucking View Post
    there is no way to by pass it i tryed everything i could to by pass the one i have in my volvo.im taking the truck to volvo to have them remove it all together its the only way.
    You need Cummins Insite software to disable ICON. Jumping starting wires is not all!

    DD use OI. To disable it DDRS is required.

    Gentelmen! you work with computer controlled truks! use all tools!

Page 1 of 3 123 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •