Truckers Report Jobs

Find Trucking Jobs

Company Driver Company Driver Dry Van Dry Van Flatbed Flatbed Refrigerated Refrigerated Specialized Specialized Owner Operator Owner Operator
More Trucking Job Searches ⌄ Fewer Trucking Job Searches
⌃

ddec iv ecm not working

Discussion in 'Trucks [ Eighteen Wheelers ]' started by truckerbangin, Aug 29, 2014.

Page 1 of 2
  1. Aug 29, 2014 #1
    truckerbangin

    truckerbangin Light Load Member

    256
    43
    Jan 22, 2013
    0
    running a detroit diesel series 60 ddec iv and its the second time a ecu has died on me. same scenario on two different occasions trucks came to yard running fine next morning trucks roll over but wont start. has any one had issues with ecm's going dead over night?
     
    truckerbangin, Aug 29, 2014
    truckerbangin, Aug 29, 2014
    #1
  2. Truckers Report Jobs

    Trucking Jobs in 30 seconds

    Every month 400 people find a job with the help of TruckersReport.

  3. Aug 29, 2014 #2
    Heavyd

    Heavyd Road Train Member

    7,625
    6,027
    Feb 4, 2009
    0
    Struck by lightning during the night.
     
    Heavyd, Aug 29, 2014
    Heavyd, Aug 29, 2014
    #2
  4. Aug 30, 2014 #3
    sailboatjim

    sailboatjim Light Load Member

    292
    173
    Aug 27, 2014
    Boston, Mass
    0
    Someone exchanged it during the night.
     
    sailboatjim, Aug 30, 2014
    sailboatjim, Aug 30, 2014
    #3
  5. Aug 30, 2014 #4
    xsetra

    xsetra Road Train Member

    4,925
    6,583
    Aug 21, 2011
    0
    I have a Cummin's, but mine went bad while I was starting truck. Motor started but cel and sel came on so I shut motor off. Read codes. Tried to start and motor would crank but not start. I was jump starting. I was told the ECM had a power surge while starting.
    Is your ECM bad or did you just lose power to it.
     
    xsetra, Aug 30, 2014
    xsetra, Aug 30, 2014
    #4
  7. Aug 30, 2014 #5
    baha

    baha Road Train Member

    4,137
    2,834
    Jul 25, 2013
    ga
    0
    ECM. has a small batt. built into it, if it goes bad truck will not run, 1st be sure truck is powering the ecm with key on?
     
    baha, Aug 30, 2014
    baha, Aug 30, 2014
    #5
  8. Aug 31, 2014 #6
    truckerbangin

    truckerbangin Light Load Member

    256
    43
    Jan 22, 2013
    0
    thats the first thing i did when i took ecm off
     
    truckerbangin, Aug 31, 2014
    truckerbangin, Aug 31, 2014
    #6
  9. Oct 19, 2014 #7
    dustinbrock

    dustinbrock Road Train Member

    1,306
    900
    Apr 19, 2012
    saskatoon,sk
    0
    Same happened to me. There is a fuse right at your batteries that runs to ecm. Check the fuse and make sure it's clean..... there's a few of em so check em all.
     
    dustinbrock, Oct 19, 2014
    dustinbrock, Oct 19, 2014
    #7
  10. Oct 19, 2014 #8
    dustinbrock

    dustinbrock Road Train Member

    1,306
    900
    Apr 19, 2012
    saskatoon,sk
    0
    dustinbrock, Oct 19, 2014
    dustinbrock, Oct 19, 2014
    #8
  11. Oct 20, 2014 #9
    Exiled

    Exiled Light Load Member

    181
    29
    Apr 20, 2013
    0
    Orange & green wires are the ground, on the right ecm connector might went bad
     
    Exiled, Oct 20, 2014
    Exiled, Oct 20, 2014
    #9
  12. Oct 21, 2014 #10
    Pablo-UA

    Pablo-UA Road Train Member

    7,604
    1,640
    Oct 11, 2010
    Borispol, Ukraine
    0
    what kind of internal damege? Remove back cover and inspect
     
    Pablo-UA, Oct 21, 2014
    Pablo-UA, Oct 21, 2014
    #10
  • Truckers Report Jobs

    Trucking Jobs in 30 seconds

    Every month 400 people find a job with the help of TruckersReport.

    • Page 1 of 2