MID 128 SID 211 5 Volt DC Supply

Discussion in 'Volvo Forum' started by xiipercent, Jan 7, 2012.

  1. xiipercent

    xiipercent Medium Load Member

    456
    129
    Mar 19, 2007
    0
    Fun w/volvo's.

    I'm excited to figure this one out.

    FMI 4

    symptoms include : poor driveability, strange information displayed on cluster

    ??? poor driveability from a 5 volt dc supply?

    This weekends other exciting maintenance include replacing abs sensor and bracket on Right Front brakes, a new headlight assembly for driver side(mine has the clarity of a clam shell) and a rear of cab light bulb....yehaaa
     
  2. Truckers Report Jobs

    Trucking Jobs in 30 seconds

    Every month 400 people find a job with the help of TruckersReport.

  3. Pablo-UA

    Pablo-UA Road Train Member

    7,604
    1,640
    Oct 11, 2010
    Borispol, Ukraine
    0
    any sensor ore sensor wiring short and low sensor power supply

    disconnect all sensors one by one to find faulty one.

    Start with oil pressure sensor, crankcase pres. sensor, fuel pressure sensor.

    Inspect wiring
     
  4. xiipercent

    xiipercent Medium Load Member

    456
    129
    Mar 19, 2007
    0
    pablo,
    thank you.
    where's your tip jar...paypal?
     
  5. Pablo-UA

    Pablo-UA Road Train Member

    7,604
    1,640
    Oct 11, 2010
    Borispol, Ukraine
    0
    I have no pay pal

    btw, have you solved your problem?
     
  6. xiipercent

    xiipercent Medium Load Member

    456
    129
    Mar 19, 2007
    0
    no- it must be related to my 'oil can' dash monitor, which still reads zero.

    I can't figure out how the sensor cord attaches.it wiggles in both directions; clock-counter clock.
    i'm sensitive to apply to much 'hand torgue' to the snaplock??

    same for the crankcase sensoe that was replaced last month.
     
  7. Pablo-UA

    Pablo-UA Road Train Member

    7,604
    1,640
    Oct 11, 2010
    Borispol, Ukraine
    0
    what engine? D12D ore D13?
     
  8. xiipercent

    xiipercent Medium Load Member

    456
    129
    Mar 19, 2007
    0
    2006 vnl 780 d12 6n434786:biggrin_25514:
     
  9. sbaumann14

    sbaumann14 Road Train Member

    1,144
    1,252
    Sep 1, 2010
    Rhinelander, WI
    0
    I'd start with the crank sensor that was just replaced...might not have tightenedit all the way
     
  10. Pablo-UA

    Pablo-UA Road Train Member

    7,604
    1,640
    Oct 11, 2010
    Borispol, Ukraine
    0
    it is D12D. The last D12 in Volvo... Some D12F were in Renault but in F version with ECM like on D13.

    Ok, where to find problem.... really everywhere. Dealers use brake boxes to find bad sensor ore bad wirng. I use the other way - separate ECM connector and check all sensors one by one, I have wiring diagram of D12D EU and US versions, so I can post it to you. Simple DVOM really helps
     
  11. xiipercent

    xiipercent Medium Load Member

    456
    129
    Mar 19, 2007
    0
    so.
    Volvo dealer is saying that the 5volt was traced to the egr#2.

    my response- If you replace the egr#2 , will it solve the "zero" reading on my oil pressure dash gauge? (because they say it operates off the same circuit.)
    If I'm not throwing any fault codes for EGR, why would replacing the unit solve the 'short' problem. should'nt they instead look for the 'short' problem?
     
  • Truckers Report Jobs

    Trucking Jobs in 30 seconds

    Every month 400 people find a job with the help of TruckersReport.