Truckers Report Jobs

Find Trucking Jobs

Company Driver Company Driver Dry Van Dry Van Flatbed Flatbed Refrigerated Refrigerated Specialized Specialized Owner Operator Owner Operator
More Trucking Job Searches ⌄ Fewer Trucking Job Searches
⌃

Ultrashift (freightliner smartshift) Not going into gear after clutch replacement

Discussion in 'Freightliner Forum' started by Catliner, Oct 24, 2015.

Page 1 of 2
  1. Oct 24, 2015 #1
    Catliner

    Catliner Light Load Member

    164
    39
    Jan 5, 2014
    Thompson, GA
    0
    I bought a Freightliner Columbia with a bad Headgasket, Its an MBE4000 (I know its a terrible engine to many) and the Eaton Ultrashift 2 pedal. Anyway instead of reparing the heads I just changed the engine as I had a complete take out with 95k miles. I installed the new engine, started it up and went to place it in gear, it jumped into gear but then jumped out within a fraction of a second and threw a code ECU130 on the insturment panel display. I didnt remove the transmission durring the swap, I did put a new DM Centrifical Clutch in durring the swap so I didnt have to remove it twice. The problem is that it wont go into gear, It tries once after start up but after that it changes from N to F1 to F2 to R on the gear selector display in the dash like its lost its mind..
     
    Catliner, Oct 24, 2015
    Catliner, Oct 24, 2015
    #1
  2. Truckers Report Jobs

    Trucking Jobs in 30 seconds

    Every month 400 people find a job with the help of TruckersReport.

  3. Oct 24, 2015 #2
    AModelCat

    AModelCat Road Train Member

    29,149
    158,436
    Jul 7, 2015
    Canuckistan
    0
    Did it shift before the engine swap? Did you replace the engine with the same brand and model?
     
    AModelCat, Oct 24, 2015
    AModelCat, Oct 24, 2015
    #2
    Catliner Thanks this.
  4. Oct 24, 2015 #3
    QUALITYTRUCK

    QUALITYTRUCK Road Train Member

    1,804
    1,765
    Jun 14, 2009
    romulus,mi
    0
    The new engine ecm has to be programmed for an automatic transmission to work correctly.
     
    QUALITYTRUCK, Oct 24, 2015
    QUALITYTRUCK, Oct 24, 2015
    #3
    flood and AModelCat Thank this.
  5. Oct 24, 2015 #4
    Catliner

    Catliner Light Load Member

    164
    39
    Jan 5, 2014
    Thompson, GA
    0
    Im using the old ECM on the new block. Transmission code is 27. Replaced the engine with an identical MBE4000. I dont have any idea if it worked when the old engine blew. The previous owner is unreachable
     
    Catliner, Oct 24, 2015
    Catliner, Oct 24, 2015
    #4
  7. Oct 24, 2015 #5
    flood

    flood Road Train Member

    4,161
    4,031
    Dec 25, 2010
    0
    you'll need to call the dealer to find out for sure what the code is

    but if I remember right ecm130 is the Message Identifier for the Transmission
    the instrument cluster is not seeing the transmission control module

    you may need to be towed to a dealer to have the dash, ecm, or trans reflashed
     
    flood, Oct 24, 2015
    flood, Oct 24, 2015
    #5
  8. Oct 24, 2015 #6
    Catliner

    Catliner Light Load Member

    164
    39
    Jan 5, 2014
    Thompson, GA
    0
    Code 27 is clutch related. Maybe the clutch needs recalibration after I installed it with the engine.
     
    Catliner, Oct 24, 2015
    Catliner, Oct 24, 2015
    #6
    flood Thanks this.
  9. Oct 25, 2015 #7
    Bonafide

    Bonafide Bobtail Member

    1
    1
    Oct 25, 2015
    0
    Engine must be revved up over 1500 rpm to unlock new clutch. Code 27 means that the clutch is locked up so the trans input shaft is turning and it wont go in gear.
     
    Bonafide, Oct 25, 2015
    Bonafide, Oct 25, 2015
    #7
    Catliner Thanks this.
  10. Oct 26, 2015 #8
    baha

    baha Road Train Member

    4,137
    2,836
    Jul 25, 2013
    ga
    0
    Are the u shaped hold down clips still in pressure plate , look in insp. plate under trans. and look when clutch is pushed to floor to see if pressure plate is moving all the way back out if not the clips that came on pressure plate can be pry out if they wont fly out with clutch press in at 1500rpm, also ck if main shaft is being stopped from turning by clutch brake?
     
    baha, Oct 26, 2015
    baha, Oct 26, 2015
    #8
  11. Oct 26, 2015 #9
    Catliner

    Catliner Light Load Member

    164
    39
    Jan 5, 2014
    Thompson, GA
    0
    Called eaton. The clutch is not unlocking. Gotta pull it out again
     
    Catliner, Oct 26, 2015
    Catliner, Oct 26, 2015
    #9
  12. Oct 26, 2015 #10
    Catliner

    Catliner Light Load Member

    164
    39
    Jan 5, 2014
    Thompson, GA
    0
    Its a two pedal
     
    Catliner, Oct 26, 2015
    Catliner, Oct 26, 2015
    #10
  • Truckers Report Jobs

    Trucking Jobs in 30 seconds

    Every month 400 people find a job with the help of TruckersReport.

    • Page 1 of 2