Ok this is a dumb one because I KNOW it’s not hard.
but you drive into the truck stop. Each row has angled spots....for the life of me...I still can’t figure out how to get into these spots!
I know I’m being stupid, I accept I’m going to get chewed out in this thread, but someone help me out because mentally, I just can’t visualize it!
Parking in truck stops
Discussion in 'Questions From New Drivers' started by Penumbra, Nov 16, 2019.
Page 1 of 5
-
Maverick Griff, Sirscrapntruckalot, TravR1 and 3 others Thank this.
-
Trucking Jobs in 30 seconds
Every month 400 people find a job with the help of TruckersReport.
-
Back in?? Just kidding. Unfortunately a lot of truckstops were designed by people that had never even seen a truck and set the parking lots up for all blindside parking. Hit a stop during the day when they are not crowded and practice. The more you back the better you will get.
Maverick Griff, Dino soar, Cattleman84 and 9 others Thank this. -
Midlife Trucker, Odin's Rabid Dog, PE_T and 7 others Thank this.
-
Rideandrepair and laaylor Thank this.
-
Half the veteran drivers just park at the entrance, fuel pumps or CAT scale and don't care if the truck stop burns down around them or they shut down all interstate commerce east of the Mississippi. You are learning a new skill not trying to learn how to use a bucket. Your school probably did very little to show you and pushed you toward the DMV.
If you can make a diagram or post a pic or example, it may be easier to help you. When you are driving down the "road" of the truck stop in front of this angled parking, is your tractor's driver or passenger door closest to the empty parking spot you are trying to back into? Most of the spots dedicated to the Idle-Aire service expect you to nose into the parking or require a blind-side back and that's more difficult for everyone.
Just remember, you are learning a mechanical skill. There is almost no reason you would already know how to do it anymore than a kid raised in the city would know how to tie 15 different knots in a rope. Even watching a video a couple of times would not be enough. Until you tie the knots, step-by-step, you won't REALLY have learned it. Then you have to practice tying the knots, one at a time, and over and over and over until you can do it without thinking very hard of each step. I worked for a flight school. It takes a good teacher and a willing student, and a GOOD step-by-step procedure and then almost anyone can learn any skill. I doubt you've had ANY teachers in trucking that are very good and each one probably had some sloppy and rushed folksy way for every skill and it was mostly "come on, do that thing NOW, oh heck, no. Now, turn, turn, STOP!!!!!"
Essentially all truck stop parking is a 45 degree or a 90 degree back and most are on the driver-side. Watch YouTube until you find a video that makes sense to you and watch it over and over until you understand it and can find where the tractor drive tires and the trailer tandems are when the key steps are started or where they should be when you are doing it. Someone need to show and tell you what to look at, when to look at it, how to judge if that thing is too far left or too far right of where you want it. And then you need to be shown and practice how to correct for too far left/right. LOTS of veteran drivers still correct in EXACTLY the wrong way when the trailer is too far left/right if where they want it.
One thing to think about, it helped me, but it may not work for you. Imagine you are already parked in the spot. Now imagine driving straight out of that parking spot toward the setup postion you would use to begin baking into the spot. Visualize the steering commands you would make while driving forward. Write them down it you have to or just remember them. There are dozens of ways to teach or explain the method. You can always sit somewhere and watch other drivers park in spaces if you ever see that happening instead of the guys just noseing in or parking along the curb at the truck stop entrance. Those guys should have their CDL suspended in many cases.ruckusftlc, Dino soar, seagreg and 4 others Thank this. -
Rideandrepair and FlaSwampRat Thank this.
-
If the parking spots are at a angle that mean you're supposed to be coming in at a certain direction. If it's hard for you to back in your probably coming in the wrong direction
88228822, starmac, bryan21384 and 3 others Thank this. -
What I don't get is when I see places where the spots are angled to make it Blind Side.
Maverick Griff, tscottme and Rideandrepair Thank this. -
It's pretty easy to nose in and back out. That's how it's designed.
Rideandrepair Thanks this. -
it’s that standard situation where you pull in and you have a row of trucks on either side of you both angled the same direction.
it FEELS to me, like I’m just supposed to pull past the spot then blindside in, but I don’t want to experiment in a full house obviously lol
since I’m dedicated, I sleep at the same truck stop generally. The spots there are angled, but it’s only one row, so you just straight back in. However they sent me on a run to Kentucky so I’m having to learn.
last night I just went nose first lol ### beside me clipped my trailer tandem while I was asleep woke up to a bent rim and a flattscottme and Rideandrepair Thank this.
Trucking Jobs in 30 seconds
Every month 400 people find a job with the help of TruckersReport.
Page 1 of 5