PLEASE HELP - My automatic transmission truck wont go into gear

To much Electronics

 

I do not show a code "88" in my book, so I am helpless at the moment..

Have you checked for power on the TCM? This test is critical as nothing else will work with a no/low power issue..

Could you tell me which transmission you actually have? I have seveal manuals, which I can send in PDF format if you have an email addy (PM to me)
Alternatively, get in a tech that has a PC diagnostic, may be cheaper in long run...

.... Philip

 

To much electronics involved in this problem by the sound of it.

So the systems is flashing 88 or two number 8's. It then shows N and then flashes F.

Hum... sounds like a ground fault or broken/bad wire or failty component or a messed up cpu processing unit or a electrical/ground falt from the trailer.

I have no idea what an XY shifter is, but to me it sound like someone BS you.

If the trailer ABS is on, maybe there is a groumd falt coming from the trailer, unhook the power cord from the trailer and shut off the truck for 5 minutes and try again.

Now for fun if you go by the code 8 8 N F... it may just mean Now 8 you dubbled F###ed

 

Found this post from June 27,2007

looks like this is a very common problem.

[h=1]Thread: Eaton Ultra Shift on Volvo, Pete, & KW[/h]
http://www.thetruckersreport.com/tr...rs/23537-eaton-ultra-shift-volvo-pete-kw.html



06.27.2007

#1​

Truckin Juggalo

Medium Load MemberMember SinceAug 2006LocationMadisonville, TNTrucker?8 YearsAge31Posts340Thanks0Thanked: 23 Times

[h=2]Eaton Ultra Shift on Volvo, Pete, & KW[/h]

I am Currently driving a Vovlo VNL 780 with a Auto Shift transmission i have

Eaton Fuller Ultra Shift
Its the one without the Clutch just break and Gas
Has Push Button R,N,D,Manual,L

and if you have one of these let me and experience this problem i am going to post the problem and tell you what can fix it..

My Truck has a Difficult time going into Neutral like if you Pull into a fuel island and stop then put it in neutral it will beep at you, Sometimes it goes into neutral and when u turn the truck back on it will beep at you like it wasnt placed into neutral (which takes upwards of 30 minutes to get it started)

It's incapable of Automatically shifting in City Traffic
what i mean is it misses Every Up shift and Down Shift just keeps Revving but never goes into Gear, you have to manually shift engine for it to work and run your RPM's at 20 in each gear for it to take the next Gear

Has problem on Take off at 4,5,6,7 gears mainly 5,6 Gears Engine Keeps Revving but Transmission never goes into gear

On the Down shift it doesn't down shift until about 7 rpm's and it SLAMS into 9th gear and Jerks the hell out of the truck like you just been rear ended

It has a problem going into R and D (1,2 gear) it just keeps flashing the number in the Display and takes 20-60 seconds or more to go into gear
IF you get it to go into Gear you press the Gas and it slips out of gear jumps 2-3 RPM's and SLAMS back into gear and Jerks the truck.. OR falls into Neutral


Trouble Shooting
-Check Fuel Filter Level if over 1/2 way full drain to 2 inches from the bottom
-Drain Air tanks DAILY
-Load Test Batteries Replace any bad battery they send Confusing signals to ECM
-If Problem Persists the next thing i found out was that i a Faulty Transmission Wiring Harness and had it Replaced which cured most of the problems
-RANGE CONTROL SENSOR! is the key that will be replaced next week im driving it as is to make money till i go on hometime

I talked to a Transmission Mechanic and they told me that thing goes out alot on the Eaton Transmissions... and that you will Never Run into that problem on a Freightliner just on the Volvo's, Pete's and KW's that have the pushbutton set up Freightliner uses Smartshift and operantly they figured out how to fix that problem..​

​

 

The XY shifter, is an electro/mechanical component containing 2 electrical shift motors which are responsible for moving the shift gate on top of the transmission, It gets instructions from the TCU... The TCU MUST HAVE a good clean power supply...

... Philip

 

XY shifter... lol.

Sounds like it was through up by a grade 6 math teach doing algebra.

X factor equallys this unknown value and Y factor equully this unknown value.
At least we know what the F value is, worthless. And the N value is your not going any where.

X+Y+88+N= F ..... looks like algebra to me and still makes no sence.

XY shifter seam to be a useless piece electronic junk attached to a transmission.

 

Yep, that really answered the guy's question.