2.79 Rears :/

Discussion in 'Trucks [ Eighteen Wheelers ]' started by Jerzey, Jun 19, 2016.

  1. Jerzey

    Jerzey Bobtail Member

    15
    1
    Jun 19, 2016
    0
    Hello fellow logistic specialists
    I had a 2004 Freightliner Columbia. It has a Detroit 12.7 (complete inframe Feb 2015...less than 100k on inframe). It has an Eaton Fuller 10.

    Here is my dilemma...

    I've replaced a lot of parts along the way. But I'm faced with wanting to sell it due to a lack of pulling power when facing hills/mountains. Before I make a rash decision, I would like to know what my options are as far as replacing/rebuilding the rears and pricing associated with it.

    Thanks in advance ;)
     
  2. Truckers Report Jobs

    Trucking Jobs in 30 seconds

    Every month 400 people find a job with the help of TruckersReport.

  3. Old school 362

    Old school 362 Medium Load Member

    392
    249
    Mar 6, 2016
    Pensacola Fl
    0
    Call truck pro. I just picked up 3.55 rears for my w900. Both for 4000.00 . Pain that they wanted old befor getting new. Fore the core. Then I put all new bears in wheels and out put shaft. In short spend few bucks now save tons later. But I have a barn to complete task.
     
  4. Jerzey

    Jerzey Bobtail Member

    15
    1
    Jun 19, 2016
    0
    Great to know! Thanks so much ;)
     
  5. WitchingHour

    WitchingHour Road Train Member

    3,422
    2,142
    Apr 1, 2011
    Broomfield, CO
    0
    What's the drive ratio of your transmission? If you're running a direct drive, switching to 3.55s is going to be closer to running 4.88s with an OD transmission than what you're expecting. Also, what size tires are you running? You need to factor all of that in to figure out where you're going to be at for cruising speed. To that end, swapping tire sizes might be a more economical way to get you to where you want to be vs. swapping out rears.
    There's a formula for figuring it all out...
    (##60)/(B*C*D)
    A = engine RPMs
    B = Rear end gear ratio
    C = Transmission final drive ratio
    D = Tire revolutions per mile

    So if you're running a direct drive transmission now with those 2.79s and we'll say tires which give you 513 revolutions per mile, and you wanted to see where you were at 1500 RPMS...
    (1500*60)/(2.79*1*513) = 62.88....

    So you'd be running between 62 and 63 MPH at those RPMS. Change it up to 3.55s...

    (1500*60)/(3.55*1*513) = 41.419.....

    See the difference? Knowing your transmission drive ratio and tire revs per mile is important. The guy running 3.55s probably isn't using the same transmission as the guy running 2.64s or 2.79s.
     
  6. Jerzey

    Jerzey Bobtail Member

    15
    1
    Jun 19, 2016
    0
    Thanks for the reply!
    How do I figure out my transmission drive ratio? I'm running 295/75/22.5 low profile. I'm just at 1500rpm at 65mph.
     
  7. sdaniel

    sdaniel Road Train Member

    5,511
    4,416
    Sep 7, 2011
    Pelham N.C.
    0
    Sounds like a direct. Find the model number and call a dealer.
     
  8. WitchingHour

    WitchingHour Road Train Member

    3,422
    2,142
    Apr 1, 2011
    Broomfield, CO
    0
    On the right side of the dash, in front of the passenger seat, there's a panel you can remove and you should be able to see a spec sheet once you do... it will include the nomenclature of the transmission (e.g., RTLO16909A, FRO16210C, etc.), and you can determine it from that.
     
  9. ROBSREDFORD

    ROBSREDFORD Light Load Member

    266
    139
    Sep 2, 2008
    MIDLAND, NC
    0
    Get ahold of rebel127. Leave 2.79 w direct Trans get his ecm tuning with 171702 Borg Warner turbo. You will love it
     
  • Truckers Report Jobs

    Trucking Jobs in 30 seconds

    Every month 400 people find a job with the help of TruckersReport.