2001 international 9400i vibration problems

Discussion in 'International Forum' started by masterdisaster, May 21, 2011.

Page 1 of 2
  1. May 21, 2011 #1
    masterdisaster

    masterdisaster Bobtail Member

    5
    0
    May 21, 2011
    hamilton ohio
    0
    I have a 2001 international 9400i it has a vibration in the floor boards i changed carryer and 1 u joint that i thought was bad i had a couple front drive wheel bearings loose fixed all that and still has the same problem can any body tell me something else that might help thanks
     
    masterdisaster, May 21, 2011
    masterdisaster, May 21, 2011
    #1
  2. Truckers Report Jobs

    Trucking Jobs in 30 seconds

    Every month 400 people find a job with the help of TruckersReport.

  3. May 21, 2011 #2
    losttrucker

    losttrucker Road Train Member

    1,436
    1,041
    Mar 9, 2008
    greenville,nc
    0
    You may wanna get your rear diff checked. I had that same problem until a bearing in the chunk came apart and cost me a re-build.
     
    losttrucker, May 21, 2011
    losttrucker, May 21, 2011
    #2
    masterdisaster Thanks this.
  4. May 21, 2011 #3
    Bent Wrench

    Bent Wrench Medium Load Member

    588
    205
    Aug 11, 2009
    Cornholio, OR
    0
    Don't drive around with the bags dumped! :^)


    Are the U joints timed correctly?
     
    Bent Wrench, May 21, 2011
    Bent Wrench, May 21, 2011
    #3
    masterdisaster Thanks this.
  5. May 21, 2011 #4
    masterdisaster

    masterdisaster Bobtail Member

    5
    0
    May 21, 2011
    hamilton ohio
    0
    is it a ez to change that bearing out if i do it my self
     
    masterdisaster, May 21, 2011
    masterdisaster, May 21, 2011
    #4
  7. May 21, 2011 #5
    masterdisaster

    masterdisaster Bobtail Member

    5
    0
    May 21, 2011
    hamilton ohio
    0
    yes everything is in line like it is soppost to be
     
    masterdisaster, May 21, 2011
    masterdisaster, May 21, 2011
    #5
  8. May 21, 2011 #6
    losttrucker

    losttrucker Road Train Member

    1,436
    1,041
    Mar 9, 2008
    greenville,nc
    0
    To me no....I had to have the whole chunk rebuilt as it came apart pulling out of a dock.
     
    losttrucker, May 21, 2011
    losttrucker, May 21, 2011
    #6
    masterdisaster Thanks this.
  9. May 22, 2011 #7
    masterdisaster

    masterdisaster Bobtail Member

    5
    0
    May 21, 2011
    hamilton ohio
    0
    is that the front drive or rear that the bearing went in
     
    masterdisaster, May 22, 2011
    masterdisaster, May 22, 2011
    #7
  10. May 22, 2011 #8
    losttrucker

    losttrucker Road Train Member

    1,436
    1,041
    Mar 9, 2008
    greenville,nc
    0
    The rear drive...and if yours does break don't do like I did and throw the power divider on and bob tail to the repair shop....drop your trailer and get a wrecker because I also ruined an axle by being cheap.
     
    losttrucker, May 22, 2011
    losttrucker, May 22, 2011
    #8
    masterdisaster Thanks this.
  11. May 22, 2011 #9
    masterdisaster

    masterdisaster Bobtail Member

    5
    0
    May 21, 2011
    hamilton ohio
    0
    i checked all the rears no metal shavings in the oil where i changed it so dont think it is a rear but i dont know i am at my last straw
     
    masterdisaster, May 22, 2011
    masterdisaster, May 22, 2011
    #9
  12. May 23, 2011 #10
    Heavyd

    Heavyd Road Train Member

    7,829
    6,279
    Feb 4, 2009
    0
    When do you feel this? Does it go away if you are coasting? Does it change if you press the clutch pedal? Certain speed range? Loaded or unloaded?
    Is your air ride height correct?
     
    Heavyd, May 23, 2011
    Heavyd, May 23, 2011
    #10
    Rodneyb3001 Thanks this.
  • Truckers Report Jobs

    Trucking Jobs in 30 seconds

    Every month 400 people find a job with the help of TruckersReport.

    • Page 1 of 2