Advice Please - Connex 4300-300

Discussion in 'CB Radio Forum' started by 1989 Pete, Jun 1, 2011.

  1. 1989 Pete

    1989 Pete "Pine Tree Eater"

    Hello just purchase a Connex 4300 300 took it to the cb shop to have it bench tested everything checked out fine However, when I hooked it up in my truck I can't get any receive on it , another driver had me switch to another channel that he was on he said he could hear me but it was very distorted fuzzy unclear( I get the same thing from drivers when they talk back to me unclear distorted)...I'm hooking this up to a Wilson 5000 antenna everything new but the coax wire....what possibly could be my problem? Oh Yea I'm new to this

    Thanks for any input
     
  2. Truckers Report Jobs

    Trucking Jobs in 30 seconds

    Every month 400 people find a job with the help of TruckersReport.

  3. WA4GCH

    WA4GCH Road Train Member

    3,324
    577
    Aug 12, 2009
    Seminole Florida
    0
    sounds like a antenna problem do you have a way to check your antenna
     
  4. jugganaut

    jugganaut Bobtail Member

    47
    6
    May 6, 2011
    holy,denial
    0
    what kinda truck u n
    do not key that thing up again or ul pop the finals till this issue has been fixed
     
  5. Yup

    Yup Medium Load Member

    569
    129
    Apr 2, 2011
    Everywhere,USA(Texas)
    0
    No he wont pop the finals :biggrin_25518:
    He said the coax wasnt new so I would look at R/R to remove that as a possible cause.
    If the mount is well used I would check the nylon washer and make sure
    it hasnt been crushed and is grounding out the antenna.

    Next option would be to return the stick and get a refund or replacement.

    The Wilson line of antenna's "USED" to be a favored choice by many
    Many still buy them without relizing they are not the same as they were
    in early years. Barjan has cut QC on every item they have a hand in
    and the Wilson 2K/5K are not worth the $30 most now places ask for them.
     
  6. Rat

    Rat Road Train Member

    I had a similar problem. I have a connex 4600 turbo. Audio was kinda garbbled and cutting in and out. almost like talking into a tin can with a string stuck in the bottom of it. I thought it might have been a radio issue so I took it down and put up my Cobra 29 stealth instead. I happened to notice that the SWR was going real high when bouncing down the road. I stopped and hooked up an external meter and did some more checking. I traced it down to a possible break in the coax right at the radio. I temporarily strung a different coax and the problem went away.


    I don't know what kind of truck you have but I hate the setup they used in the older petes and the Volvos. This is the setup were they use the CB antennas for the am fm radio also. They run everything through a little box under the dash. Mind you, this box does not like extra power and the 4300-300 will burn it out in a hurry.

    Also if the truck is set up with factory cophased antennas then you must run two antennas. Either that or get a single phased coax so that you can run just one antenna.

    Single antennas require 50 ohm coax while cophased or dual antennas require two equal length 75 ohm coax.

    I had a 4300-300 for a short while, It got ripped off out of my truck in the back in the company yard. Sure wish I had it back.
     
  7. groundpounder

    groundpounder Road Train Member

    2,569
    1,039
    Nov 13, 2009
    0
    make sure your on AM and not FM or SSB (if it has SSB)..
     
  • Truckers Report Jobs

    Trucking Jobs in 30 seconds

    Every month 400 people find a job with the help of TruckersReport.