Do you float gears or double clutch?

Discussion in 'Questions From New Drivers' started by Unkl L, May 16, 2012.

  1. Treefork

    Treefork Road Train Member

    2,883
    1,459
    Mar 22, 2008
    Northeast Indiana
    0
    Sure about that?
     
  2. Truckers Report Jobs

    Trucking Jobs in 30 seconds

    Every month 400 people find a job with the help of TruckersReport.

  3. DanS

    DanS Light Load Member

    88
    34
    Apr 14, 2012
    edgewater florida
    0

    I had a super trucker that used this triple clutch methed told me the only right way to do it ... Is to have your super clutch foot at a 45degree angel pointing south and looking to the west while texting with your left hand (phone must be pointing east) stearing with your right leg and shifting with your right hand...

    :biggrin_25524:

    :biggrin_25521:
     
    DirtyBob and -MadMax- Thank this.
  4. pattyj

    pattyj Road Train Member

    22,474
    20,134
    Jul 19, 2008
    Sioux City,ia
    0
    The less I have to use the clutch the better off I am.The trks I drive will beat ya up if you're not careful.I float as much as possible.But if I can't get it into gear i'll double clutch.
     
  5. RedSkys

    RedSkys Bobtail Member

    22
    8
    Aug 30, 2010
    Saskatoon, SK
    0
    Float up, sometimes use the clutch to pop out of gear on the way down if I need to shift fast.
     
  6. Eaton18

    Eaton18 Road Train Member

    1,755
    1,103
    Sep 3, 2011
    Waverly, KS
    0
    Glance at your tach (shows your rpms). I have a 13spd, and most of the time I can shift smoothly around 1500-1550 rpms. Also listen to the engine, so you can quit looking at the tach.

    I was also taught a simple mathematical formula that basically tells you what gear you should be in at given speeds. You add the 2 numbers of the speed (mph). Example 45 mph.. 4+5 = 9, so you should shift into 9th gear.

    Don't worry about the speed in the lower first 4 gears. You go through them before you get across an intersection. It's the upper 4 or so that this would be applicable to.

    15 mph.... 1+5 = 6, ie; 6th gear
    25 mph.... 2+5 = 7.... 7th gear
    35 mph.....3+5 = 8.... 8th gear

    you get the idea. Just pay attention to your engine RPM, both up and downshifting. When you downshift, your engine RPM might be down around 1100.

    While learning if your grinding, gently hold the lever while you get that grinding, and depending on where your engine RPM is, either increase it or decrease it, and you will feel the lever slide in. MAKE A MENTAL NOTE OF WHERE THIS WAS. Then next time you'll know.

    Now this comes from a driver (still steering wheel holder), with a tremendous amount of time (6 mos now) driving a big truck. However applying what I've told you, which I was taught by some very experienced drivers, I can float with only scratching a gear every now and then. Most of the time if I grind, it's in a "panic" situation where the a-hole 4-wheeler pulls out in front of me, trying to steal my front bumper. I just miss getting it into the right gear from my very sudden, fast, almost to a dead-stop avoiding them. Think 2-lane highway, no or the 2-foot shoulders.
     
    pattyj and davetiow Thank this.
  7. -MadMax-

    -MadMax- Light Load Member

    248
    72
    Feb 29, 2012
    Pennsylvania
    0
    You can also tell by the pitch of the grind.

    If it is higher pitch you're trying to put it in too high of a gear. Lower/slower grind, you're going too low.

    When I took my road test I dbl clutched everything. Drove my tester (future trainer) nuts. He said you'll be fine after you stop dbl clutching.

    So, 2 weeks later, I'm floating and wondering why I ever dbl clutched to start with. Which, feels almost foreign now.

    It feels so right, when it's right, they go right into gear. No grinding. But if you don't get it all the way in... it feels like you just dropped the bottom end out from your truck. Have done this twice already and I cringed both times scared to death I broke something.

    This is one of the reasons it doesn't bother me to possibly have the oldest truck in the yard. IF I break something, I won't feel AS bad. But still feel like a (insert choice expletive)!
     
  8. snowbird_89

    snowbird_89 Road Train Member

    1,006
    799
    Aug 21, 2009
    Massachusetts
    0
    I double clutch most of the time because that's how i was taught. Sometimes I try to float up shifting, but usually it won't pop out of gear or it'll grind a little when i go into the next gear. I just can't get the feeling for it. How do i float without grinding?
     
  9. OpenRoadDreamer

    OpenRoadDreamer Road Train Member

    6,225
    989
    Apr 26, 2011
    Alabama
    0
    Put it in gear at the right RPM.... Smooth as butter.
     
  10. Onetruckpony

    Onetruckpony Medium Load Member

    544
    372
    Jun 11, 2011
    0
    Floating is a two part one move deal :D

    Timing is everything, and it only comes with time.

    Hell I still make em sing once in awhile, just a little.
     
  11. loud2ns

    loud2ns Bobtail Member

    36
    5
    Dec 9, 2010
    Hudsonville, Michigan
    0
    I only use the clutch only to start and when I go into the high side when loaded.

    I used the clutch for my test like I was supposed to do and bad things happened......missed the gear and took a turn a little to fast and the tester got a little scared!!
     
  • Truckers Report Jobs

    Trucking Jobs in 30 seconds

    Every month 400 people find a job with the help of TruckersReport.