Drilling/welding Pre-cautions

Discussion in 'Trucks [ Eighteen Wheelers ]' started by 7mouths2feed, May 28, 2009.

  1. T800H

    T800H Medium Load Member

    608
    295
    Apr 2, 2010
    The Keys
    0
    [​IMG]

    See how there's no holes on the top part, but the side is full of nuts and bolts, the top is the flange, same as the bottom part.
     
  2. Truckers Report Jobs

    Trucking Jobs in 30 seconds

    Every month 400 people find a job with the help of TruckersReport.

  3. lilillill

    lilillill Sarcasm... it's not just for breakfast

    5,642
    13,471
    Nov 7, 2007
    Possum Booger, Alabama
    0
    Just a tip for drilling... use a masonry bit. They'll go through hardened steel better than any other bit.
     
  4. Goodysnap

    Goodysnap Road Train Member

    3,716
    9,022
    Jul 12, 2017
    0
    My dad had a stock of tapered fluted bits that would take a 3/8 or 1/2 hole and open it up to 3/4 or 1" in short order and with minimal effort even with a hand drill. The mag drill press , good bits and cutting oil is where it's at today. Get a double frame chassis and shorten the wheel base and you'll definatley buy one.
     
    pushbroom and spsauerland Thank this.
  5. starmac

    starmac Road Train Member

    6,639
    12,528
    Apr 11, 2019
    Fairbanks Ak
    0
    The way I always drilled a frame , was use a small bit for a pilot hole, then a tapered reamer for the size I needed. I now have a mag drill and anywhere it can be used, I use the annular cutters instead of a bit and reamer.
    I have always been told to never under any circumstances drill the flanges and never have, but my old freightliner has countless holes in the flanges that came from the factory. It started out life on the haul road as a 5 axle tractor hauling heavy, and since retired off the road has log gear in the winter swapping to side dump for dirt in the summer. So it has never had any sort of an easy life and never had a frame problem.
     
    spsauerland Thanks this.
  6. Canucklehead

    Canucklehead Medium Load Member

    375
    347
    Feb 25, 2010
    Vancouver BC
    0
    All I use for drilling holes in my frame are some M42 cobalt bits and a regular dill. They cut through like butter. But yes I also use cutting oil too.
     
    T800H Thanks this.
  7. claytonr1973

    claytonr1973 Light Load Member

    266
    289
    Jun 1, 2008
    miami,ok
    0
    Had to put my 5th wheel slider at the rear of the frame today. I used a 1/4 and 3/8 el cheapo bits and then a 5/8 reamer. Did 10 holes and all it takes is lots of pressure, low speed and some oil to keep the bits cool. The reamer cuts through like butter though. Best $65 I've ever spent.
     
  8. Ezrider_48501

    Ezrider_48501 Road Train Member

    3,845
    5,130
    Apr 2, 2011
    bismarck, nd
    0
    generally no welding or drilling on the flange area of the frame (top and bottom) the sides of the frame are ok.
     
  9. starmac

    starmac Road Train Member

    6,639
    12,528
    Apr 11, 2019
    Fairbanks Ak
    0
    I have always heard no drilling on he flange and lived by it. I can sure see where it would give one a weak point to break, but my flc freightshaker came from the factory with holes all down the top flange. lol
     
    spsauerland Thanks this.
  10. spsauerland

    spsauerland Road Train Member

    4,296
    10,887
    May 31, 2010
    West Harrison, In
    0
    See many factory spring shackle brackets and air bags with hole in lower flange but, I would never drill in the flange or lower or higher into the web than a factory bolt.
     
  11. Rainman316

    Rainman316 Bobtail Member

    1
    0
    Aug 10, 2022
    0
    Guys I need advice . So at the shop today an apprentice drilled a hole in the top flange . My bad I went out for a few minutes came back and he was almost through is it fix able
     
  • Truckers Report Jobs

    Trucking Jobs in 30 seconds

    Every month 400 people find a job with the help of TruckersReport.