Search Results

Search Again
Page 4 of 12
  1. ROBSREDFORD
    Thread

    Allison auto and c15/3406e

    I'd like to put an Allison auto behind one of these .... Think there was guy on here that did it.... The ones I have are non electronic 750...
    Thread by: ROBSREDFORD, Oct 6, 2013, 10 replies, in forum: Trucks [ Eighteen Wheelers ]
  2. ROBSREDFORD
    Post

    c15 accert rebuild

    I trade alot of trucks and work on a fair amount as well. I love an acert See more of them with over million than I have seen the 6nz/mbn...
    Post by: ROBSREDFORD, Sep 6, 2013 in forum: Trucks [ Eighteen Wheelers ]
  3. ROBSREDFORD
    Post

    I could only find 27 grease points... does anyone know where the other 4 are?

    Clutch fork and throw out bearing
    Post by: ROBSREDFORD, Aug 19, 2013 in forum: Trucks [ Eighteen Wheelers ]
  4. ROBSREDFORD
    Post

    wheel centering tools

    Tru balance centering pins work excellent
    Post by: ROBSREDFORD, Aug 18, 2013 in forum: Trucks [ Eighteen Wheelers ]
  5. ROBSREDFORD
    Post

    high flow t600 muffler

    I put 463's on alot of the under exhaust trucks. The catalytic muffler is larger in diameter. Just take floor jack under existing brackets and...
    Post by: ROBSREDFORD, Jul 28, 2013 in forum: Trucks [ Eighteen Wheelers ]
  6. ROBSREDFORD
    Post

    Fuller 18 Speed

    No difference in weight. Just same basic transmissions with few extra Torrington bearings instead of flat washers to facilitate splitting gears...
    Post by: ROBSREDFORD, Jul 17, 2013 in forum: Trucks [ Eighteen Wheelers ]
  7. ROBSREDFORD
    Post

    Cat injectors

    Are you sure they are 57size tips? What power did it make as it sat? ThanksThanks
    Post by: ROBSREDFORD, Jul 7, 2013 in forum: Trucks [ Eighteen Wheelers ]
  8. ROBSREDFORD
    Post

    Cost to swap 70" replace with 36" sleeper on Pete.

    I have done this type stuff several times and there are pros and cons...the pros....small bunk trucks bring a lot more than 10 k more in my neck...
    Post by: ROBSREDFORD, Jun 3, 2013 in forum: Trucks [ Eighteen Wheelers ]
  9. ROBSREDFORD
    Post

    Is it posssible to plug and play replace an Acert Cat with 6NZ

    The truck side wiring on acert is same as 6nz.
    Post by: ROBSREDFORD, May 30, 2013 in forum: Trucks [ Eighteen Wheelers ]
  10. ROBSREDFORD
    Post

    how to change rear diff fluids???

    So far as how to....there is a plug in the housing on the bottom....closest to the ground....usually takes a 1/2 drive ratchet or pull handle....
    Post by: ROBSREDFORD, Mar 24, 2013 in forum: Trucks [ Eighteen Wheelers ]
  11. ROBSREDFORD
    Post

    C13 high egts ....what am I missing.....

    Mark I may get blasted for this but he intake actuators are causing an inflated boost reading ......disable them and boost is less...on the c15...
    Post by: ROBSREDFORD, Feb 23, 2013 in forum: Trucks [ Eighteen Wheelers ]
  12. ROBSREDFORD
    Post

    C13 high egts ....what am I missing.....

    Update- I took the turbos off to check for exhaust housing cracks...they were ok as they were only a few weeks old.....got to looking at the...
    Post by: ROBSREDFORD, Feb 23, 2013 in forum: Trucks [ Eighteen Wheelers ]
  13. ROBSREDFORD
    Post

    C13 high egts ....what am I missing.....

    Air filters are new and boots are tight. I am pulling turbos apart to check for cracks. Boost is at spec
    Post by: ROBSREDFORD, Feb 16, 2013 in forum: Trucks [ Eighteen Wheelers ]
  14. ROBSREDFORD
    Thread

    C13 high egts ....what am I missing.....

    C13 kcb pyro gets over 1000 fairly quick and low pressure exhaust housing is pink.....air to air by itself holds 60 psi. Pump up whole engine...
    Thread by: ROBSREDFORD, Feb 15, 2013, 10 replies, in forum: Trucks [ Eighteen Wheelers ]
  15. ROBSREDFORD
    Post

    hiding an apu?

    Fridgette (spelling?) made one that looks like a Pete step box. Think they out of business but find them
    Post by: ROBSREDFORD, Jan 28, 2013 in forum: Trucks [ Eighteen Wheelers ]
  16. ROBSREDFORD
    Post

    40 pin ecm on a 70 pin engine

    There is nothing wrong with 40 pin...if you change back to 70 you will have to change cam gear back....unless looking for a Dyno queen the 40 pin...
    Post by: ROBSREDFORD, Jan 23, 2013 in forum: Trucks [ Eighteen Wheelers ]
  17. ROBSREDFORD
    Post

    2000 Pete Exhd

    7045072453
    Post by: ROBSREDFORD, Jan 20, 2013 in forum: Trucker Forum Classifieds & Trading Post
  18. ROBSREDFORD
    Post

    2000 Pete Exhd

    Truck sold thanks
    Post by: ROBSREDFORD, Jan 19, 2013 in forum: Trucker Forum Classifieds & Trading Post
  19. ROBSREDFORD
    Thread

    2000 Pete Exhd

    This is a trade in with issue. The good... it's 550 cat 2ws 70 pin , 18 speed, Coral metallic and grey, American class , 3.70 , air leaf, 260...
    Thread by: ROBSREDFORD, Jan 15, 2013, 3 replies, in forum: Trucker Forum Classifieds & Trading Post
  20. ROBSREDFORD
    Post

    2007 Pete 379 EXHD

    Bump again hawg sold
    Post by: ROBSREDFORD, Jan 15, 2013 in forum: Trucker Forum Classifieds & Trading Post
Showing results 61 to 80 of 224 Next >
Search Again
Page 4 of 12