Truckers Report Jobs

Find Trucking Jobs

Company Driver Company Driver Dry Van Dry Van Flatbed Flatbed Refrigerated Refrigerated Specialized Specialized Owner Operator Owner Operator
More Trucking Job Searches ⌄ Fewer Trucking Job Searches
⌃

C15 Acert Liner Height

Discussion in 'Trucks [ Eighteen Wheelers ]' started by 3406eStar, Jan 26, 2016.

Page 2 of 2
  1. Jan 27, 2016 #11
    Superhauler

    Superhauler TEACHER OF MEN

    12,209
    100,733
    Jan 30, 2010
    keep stroking.
    0
    When you get the soft washers use a hard washer on top of the soft ones. Oh, and mic the new spacer plate for uniform thickness. Even though it is new does not mean it is right. I have had to dig through 5 of them (brand new) to find one that is flat on a rebuild before.
     
    Last edited: Jan 27, 2016
    Superhauler, Jan 27, 2016
    Superhauler, Jan 27, 2016
    #11
  2. Truckers Report Jobs

    Trucking Jobs in 30 seconds

    Every month 400 people find a job with the help of TruckersReport.

  3. Jan 27, 2016 #12
    bubbanbrenda

    bubbanbrenda Road Train Member

    1,388
    650
    Feb 27, 2011
    Middletown,Oh.
    0
    You need to cut it to get it right. Also make sure whoever you chose is competent, not a job for the average mechanic, just my $0.02...
     
    bubbanbrenda, Jan 27, 2016
    bubbanbrenda, Jan 27, 2016
    #12
    wore out Thanks this.
  4. Jan 27, 2016 #13
    bigguns

    bigguns Road Train Member

    2,846
    6,854
    Jun 13, 2013
    Omega,GA
    0
    Truck engine machinist: can you send me a pm?
     
    bigguns, Jan 27, 2016
    bigguns, Jan 27, 2016
    #13
  5. Jan 27, 2016 #14
    Truck engine machinist

    Truck engine machinist Light Load Member

    195
    188
    Dec 2, 2011
    USA
    0
    Call me. 717-368-8532
     
    Truck engine machinist, Jan 27, 2016
    Truck engine machinist, Jan 27, 2016
    #14
    bigguns Thanks this.
  7. Feb 3, 2016 #15
    3406eStar

    3406eStar Bobtail Member

    15
    2
    Jan 18, 2013
    0
    More consistent with CAT's resin washers, but still low. 1,2,5 & 6 measure .002. 3 & 4 measure .003. Replacing the new spacer plate with the thinner version offered by CAT. .003 thinner, which will give me protrusion of .005 & .006.
    For anyone else dealing with a similar job, the part # for the washers is 7k-1977 and the thinner spacer plate is part #138-9381. My local CAT counter guy insisted that these items didn't exist. They do.
     
    Last edited: Feb 3, 2016
    3406eStar, Feb 3, 2016
    3406eStar, Feb 3, 2016
    #15
    WyoVac and Oxbow Thank this.
  8. Feb 3, 2016 #16
    Superhauler

    Superhauler TEACHER OF MEN

    12,209
    100,733
    Jan 30, 2010
    keep stroking.
    0
    Spacerplate is good. Dont use the thinner shims .030.is the as thin as I would go. Cut counter bore for the .032 or .030 shims.
     
    Superhauler, Feb 3, 2016
    Superhauler, Feb 3, 2016
    #16
    Oxbow Thanks this.
  • Truckers Report Jobs

    Trucking Jobs in 30 seconds

    Every month 400 people find a job with the help of TruckersReport.

    • Page 2 of 2