Cascadia Antenna Solutions

Discussion in 'CB Radio Forum' started by mike5511, Apr 30, 2014.

  1. RStewart

    RStewart Road Train Member

    3,169
    5,059
    Aug 21, 2015
    Norman, OK
    0
    Hey guys, I've got a cascadia & I'm planning on putting mirror mounts on both sides & running dual 5 ft tunable firestick antennas. With them angled forward a little I believe there will be enough antenna in front of the cab to work fine. I've got everything for this set up & I'll be running an older connex 3300 when I get the finals replaced in it. You all think this set up will work alright?
     
  2. Truckers Report Jobs

    Trucking Jobs in 30 seconds

    Every month 400 people find a job with the help of TruckersReport.

  3. wolverine11

    wolverine11 Road Train Member

    1,628
    1,234
    Apr 1, 2015
    0
    From reading Firesticks website it says that co-phased antenna setup is recomended for fiberglass vehicles and those lacking sufficient reflective ground plane, so based on that information in theory it should work good. I know in the past there have been some members here that tried dual antennas vs single on the Cascadias and really didnt notice much improvement but its worth a try if you dont mind spending twice the money. When I was in a Cascadia I had a Single Siro Twin Log 5' antenna on drivers side and would average 10 miles transmit and receive with standard 4 watt radio.
     
  4. wolverine11

    wolverine11 Road Train Member

    1,628
    1,234
    Apr 1, 2015
    0
    Keep in mind also that with co-phased set up your radiation pattern will be more directional towards front and back of vehicle instead of radiating 360 degrees like a single antenna does. I am currently in a '18 KWT680 and the stock antenna setup is co-phased and I have noticed the incoming signals will vary from strong to weak on curvy roads like I 24 east in Tn between Manchester and Choo Choo, but otherwise they work pretty good, low swr and good transmit and receive. It is recomended to have antennas 9' apart so the truck is 8'6" so I would put the mounts on the bracket out as far as you can so that should be 3" on each side which will be a total of 9'.
     
    RStewart and bored silly Thank this.
  5. RStewart

    RStewart Road Train Member

    3,169
    5,059
    Aug 21, 2015
    Norman, OK
    0
    Yeah co-phase has a better signal front to back than it does 360° but I don't think I'll ever notice it unless I'm on I-24.
     
    wolverine11 Thanks this.
  6. Neverready

    Neverready Medium Load Member

    406
    330
    Jul 24, 2014
    Pocomoke City, Md.
    0
    20170517_064158.jpg Well it took 2years but the mount failed. Tried simplifying the design to help new bracket last longer but antenna wouldn't tune. Cleaned up corrosion and reinstalled tuned right in with new mount.
     
    rabbiporkchop Thanks this.
  7. mike5511

    mike5511 Road Train Member

    3,156
    1,546
    May 15, 2011
    NW Arkansas
    0
    I've got a Stainless Steel one I probably won't need any more after this year if you or anybody else is looking at long term occupation in a Cascadia. It won't ever break.
     
    Neverready Thanks this.
  8. Neverready

    Neverready Medium Load Member

    406
    330
    Jul 24, 2014
    Pocomoke City, Md.
    0
    Keep me in mind when you decide to part with it.
     
  9. rabbiporkchop

    rabbiporkchop Road Train Member

    9,678
    6,545
    Feb 9, 2012
    Wapwallopen, Pa
    0
    Where did you purchase your bracket?
     
  10. volvo244t

    volvo244t Road Train Member

    1,775
    1,779
    Jun 24, 2010
    Bettendorf, IA
    0
    Didn't he have it made up by a friend of his?
     
    mike5511 Thanks this.
  11. craig_sez

    craig_sez Road Train Member

    5,570
    2,714
    Sep 5, 2013
    novascotia,Canada
    0
    You get a hot rod when you dont wrapp it b4 you tap it..
     
  • Truckers Report Jobs

    Trucking Jobs in 30 seconds

    Every month 400 people find a job with the help of TruckersReport.