Truckers Report Jobs

Find Trucking Jobs

Company Driver Company Driver Dry Van Dry Van Flatbed Flatbed Refrigerated Refrigerated Specialized Specialized Owner Operator Owner Operator
More Trucking Job Searches ⌄ Fewer Trucking Job Searches
⌃

No Start, 2009 Maxforce DT 3200

Discussion in 'International Forum' started by DieselRookie, May 10, 2017.

  1. May 10, 2017 #1
    DieselRookie

    DieselRookie Bobtail Member

    4
    2
    May 10, 2017
    0
    Hi, hope to get some guidance here. backing the truck up and just died. Just cranks and no sputtering. Sprayed little either and wanted to start. I changed the lift pump and disconnected the ICP and hand primer is pumping till it gets hard. Any more things I can check before I have to tow to the dealer?
     
    DieselRookie, May 10, 2017
    DieselRookie, May 10, 2017
    #1
  2. Truckers Report Jobs

    Trucking Jobs in 30 seconds

    Every month 400 people find a job with the help of TruckersReport.

  3. May 10, 2017 #2
    strollinruss

    strollinruss Road Train Member

    1,366
    1,697
    Jun 5, 2012
    Montgomery, TX
    0
    Dude, no starting fluid. It's something far more complicated than can be answered here.
     
    strollinruss, May 10, 2017
    strollinruss, May 10, 2017
    #2
  4. May 10, 2017 #3
    DieselRookie

    DieselRookie Bobtail Member

    4
    2
    May 10, 2017
    0
    Really?
     
    DieselRookie, May 10, 2017
    DieselRookie, May 10, 2017
    #3
  5. May 10, 2017 #4
    strollinruss

    strollinruss Road Train Member

    1,366
    1,697
    Jun 5, 2012
    Montgomery, TX
    0
    Did you figure it out? I hope so but these new trucks are tough to diagnose on the side of the road like we used to.
     
    strollinruss, May 10, 2017
    strollinruss, May 10, 2017
    #4
  7. May 10, 2017 #5
    DieselRookie

    DieselRookie Bobtail Member

    4
    2
    May 10, 2017
    0
    Yes, it was the cam sensor
     
    DieselRookie, May 10, 2017
    DieselRookie, May 10, 2017
    #5
  8. May 10, 2017 #6
    Heavyd

    Heavyd Road Train Member

    7,625
    6,027
    Feb 4, 2009
    0
    This is actually easy to somewhat diagnose on the side of the road. If you turn your key on, the stop and check engine lights are suppose to come on and go out for a bulb test. The ECM turns these lights on. If you turn on the key, and these lights do not come on, the ECM is not getting power. If they do come on, crank the engine. If the tach shows no speed while cranking, cam sensor is bad.
     
    Heavyd, May 10, 2017
    Heavyd, May 10, 2017
    #6
  9. May 10, 2017 #7
    DieselRookie

    DieselRookie Bobtail Member

    4
    2
    May 10, 2017
    0
    Exactly what it did, I was getting ready for a bad pump but it was an easy fix
     
    DieselRookie, May 10, 2017
    DieselRookie, May 10, 2017
    #7
    strollinruss and Heavyd Thank this.
  10. May 16, 2017 #8
    strollinruss

    strollinruss Road Train Member

    1,366
    1,697
    Jun 5, 2012
    Montgomery, TX
    0
    Good I'm glad to hear it, man.
     
    strollinruss, May 16, 2017
    strollinruss, May 16, 2017
    #8
  • Truckers Report Jobs

    Trucking Jobs in 30 seconds

    Every month 400 people find a job with the help of TruckersReport.