I am a newbie entering the step deck experience.
I am shopping around for loading ramps and all the accessories .
So far I have two options
option 1 discountramps.com
Step Deck Trailer Ramps & Load Leveler Combo Kits
2 Bunk Load Leveler / Modular Ramp Kit Includes:
(4) 8' x 20" aluminum ramps with pin-on ends
(2) Adjustable lower ramp support stands (18"-24")
(4) Stake pockets supports for load levelers
(6) Lumber securing clips
as well i am getting attaching hanger brackets for loading ramps and ramp stands
discount ramps also offer 8' x18" aluminum ramps same load rate 23 500 lbs per axle.
option 2 sturdy lite
Trailer Loading Ramp Master Kit 16' x 18" 25K Capacity - Trailer Loading Ramps - Trailer Parts
Kit Includes the following:
(4) 8' x 18" aluminum ramps with pin-on ends
(2) Adjustable lower ramp support stands (18"-24")
(1) Loading Ramp to Load Leveler Conversion Kit
(1) Under Trailer Storage for 4 Ramps
(1) Under Trailer Storage for 2 Ramp Stands
(2) 36" Aluminum Ramp Attaching Brackets
Made in USA
ramp load ratio 25000 lbs per axle
let me know what you think
What is the quality of this products?
Anybody using it?
Any help will be gladly appreciate it.
Thank you in advance
STURDY-LITE LOADING RAMP
Discussion in 'Flatbed Trucking Forum' started by chriscol, Jun 15, 2017.
Page 1 of 2
-
-
Trucking Jobs in 30 seconds
Every month 400 people find a job with the help of TruckersReport.
-
I have discount ramps 23k rated ramps,very good product but imo 23k rating is overkill.
-
-
Anybody using Sturdy Lite loading ramps?
Thank you in advance for the help.
Appreciate your answer
zinita17601 -
Yes. Just bought a step with Sturdy Lite ramps. Used them a couple of times worked fine. They are rated at 25k per axle. No negative comments, but then I have never used another brand to compare.
-
I've got a pair of the 8' ramps/load levelers from discount ramp.
No complaints so far.
They're a stand up company in my book.
I picked them up direct at the factory and it wasn't till I got home when I realized I was missing two of the stakes for load leveling. They overnighted them with no questions asked.
From what I've seen, a set of ramps will take more abuse than a trailer will !!!!Opendeck, snowman_w900, cke and 5 others Thank this. -
No experience with any other ramp kit besides the HD Ramps kit. I bought mine through Superior Trailers in OKC, OK.
Mine are rated 23,500 lbs each piece for a combined supported gross weight of 47,000 lbs. Most I have ever personally loaded on them was a 44k grader.
Ramps themselves will take a lot of abuse.
This is a Komatsu D61. 42k lbs. I've moved approx 19 or 20 of these with out issue.
Just a suggestion. HD Ramps sells a brace stand that goes below the rear DOT bumper. I did not have one at the time of this pic. I do now and it makes a world of difference when loading heavy up the ramps.
Hurst -
-
Excavators not so much. But dozers with tall cleats on the tracks will damage the small cross pieces that give traction.
Figure at least one of the ramps will need some kind of repair to the cross pieces after every 10 - 15 larger dozers that travel on them. Minor repair,.. $25 - $40 for a quick weld depending on how bad they want to bend you over.
Have to be careful,.. not everyone can weld aluminum properly. Easy to burn through and melt them. You have to then become a prick and get them to fabricate a new piece with out additional cost.
Hurstseth Pivarnik Thanks this. -
Trucking Jobs in 30 seconds
Every month 400 people find a job with the help of TruckersReport.
Page 1 of 2