Wheel stud extenders?

Discussion in 'Questions From New Drivers' started by JoeF2002, Apr 14, 2016.

Page 2 of 3
  1. Apr 14, 2016 #11
    JoeF2002

    JoeF2002 Light Load Member

    165
    119
    Dec 31, 2015
    Saylorsburg, PA
    0
    Correct. It's just a cover. It fits right over the existing wheel and lugs. No mods are necessary in most cases. It comes with plastic chrome lugs that you tighten onto 5 of the existing studs, using the remaining thread that sticks out past the lug nut.
     
    JoeF2002, Apr 14, 2016
    JoeF2002, Apr 14, 2016
    #11
  2. Truckers Report Jobs

    Trucking Jobs in 30 seconds

    Every month 400 people find a job with the help of TruckersReport.

  3. Apr 14, 2016 #12
    Mark Kling

    Mark Kling Technology Contributor

    10,935
    4,216
    Sep 23, 2007
    Statesville, NC
    0
    be careful of those... DOT if they get sticky can ask you if you remove it daily during your PTI to check for rust and tightness of the nuts..
     
    Mark Kling, Apr 14, 2016
    Mark Kling, Apr 14, 2016
    #12
  4. Apr 14, 2016 #13
    JoeF2002

    JoeF2002 Light Load Member

    165
    119
    Dec 31, 2015
    Saylorsburg, PA
    0
    Oh EXCELLENT tip. Didn't think of that one!
     
    JoeF2002, Apr 14, 2016
    JoeF2002, Apr 14, 2016
    #13
  5. Apr 14, 2016 #14
    speedyk

    speedyk Road Train Member

    1,837
    2,471
    Apr 8, 2015
    0
    So if the nuts reached further down through the cover holes you wouldn't need longer studs?
     
    speedyk, Apr 14, 2016
    speedyk, Apr 14, 2016
    #14
  7. Apr 14, 2016 #15
    Mark Kling

    Mark Kling Technology Contributor

    10,935
    4,216
    Sep 23, 2007
    Statesville, NC
    0
    I knew a driver that had the plastic caps and DOT asked him if he removed them each day to check the tightness of the lugs and rust.... although I don't know many drivers that carry a wrench for them....
     
    Mark Kling, Apr 14, 2016
    Mark Kling, Apr 14, 2016
    #15
  8. Apr 14, 2016 #16
    JoeF2002

    JoeF2002 Light Load Member

    165
    119
    Dec 31, 2015
    Saylorsburg, PA
    0
    Now I know to keep that wrench in the truck, just for that reason lol
     
    JoeF2002, Apr 14, 2016
    JoeF2002, Apr 14, 2016
    #16
  9. Apr 14, 2016 #17
    JoeF2002

    JoeF2002 Light Load Member

    165
    119
    Dec 31, 2015
    Saylorsburg, PA
    0
    Yes there are really only two options: longer wheel studs, or shorter nuts that can grab on better. I've even tried filing the plastic down a bit on one of the nuts, hoping that would get the threads to catch. But it didn't
     
    JoeF2002, Apr 14, 2016
    JoeF2002, Apr 14, 2016
    #17
  10. Apr 14, 2016 #18
    JoeF2002

    JoeF2002 Light Load Member

    165
    119
    Dec 31, 2015
    Saylorsburg, PA
    0
    Been searching for a while and came across this option. Not being a techy in the world of metrics and measurements though, I'm not sure if these would work.

    Does anyone happen to know: is "1/2 inch Male NPT" the same size as the "M22 x 1.5 thread pitch" I need?
     
    JoeF2002, Apr 14, 2016
    JoeF2002, Apr 14, 2016
    #18
  11. Apr 14, 2016 #19
    AModelCat

    AModelCat Road Train Member

    29,738
    165,178
    Jul 7, 2015
    Canuckistan
    0
    Likely not going to work. NPT threads are not straight like a bolt/stud. The threaded body itself is tapered for an interference fit. Going off my memory I believe 1/2" NPT threads are also coarser than the metric wheel stud threads.
     
    AModelCat, Apr 14, 2016
    AModelCat, Apr 14, 2016
    #19
    JoeF2002 Thanks this.
  12. Apr 15, 2016 #20
    speedyk

    speedyk Road Train Member

    1,837
    2,471
    Apr 8, 2015
    0
    Got another idea. Hold it on with supermagnets. Then if you're asked about inspections you can just pry them off.

    Or center drill and tap the studs.
     
    speedyk, Apr 15, 2016
    speedyk, Apr 15, 2016
    #20
  • Truckers Report Jobs

    Trucking Jobs in 30 seconds

    Every month 400 people find a job with the help of TruckersReport.

    • Page 2 of 3