Truckers Report Jobs

Find Trucking Jobs

Company Driver Company Driver Dry Van Dry Van Flatbed Flatbed Refrigerated Refrigerated Specialized Specialized Owner Operator Owner Operator
More Trucking Job Searches ⌄ Fewer Trucking Job Searches
⌃

2001 International 9100i heater/ac problem.

Discussion in 'International Forum' started by truckinglongisland, Dec 15, 2012.

Page 1 of 2
  1. Dec 15, 2012 #1
    truckinglongisland

    truckinglongisland Bobtail Member

    2
    0
    Dec 15, 2012
    0
    Wondering if you guys had any clue on what the problem could be...My blower motor isn't working. I checked all fuses and they all seem to be fine. When I turn the switch from the off position to Max, floor heat, vents, or defrosters I can hear clicking coming from the fuse box behind the glove compartment, I also hear clicking when I change the speed settings 1-4. Could it be the blower resistor? Any help would be greatly appreciated.
     
    truckinglongisland, Dec 15, 2012
    truckinglongisland, Dec 15, 2012
    #1
  2. Truckers Report Jobs

    Trucking Jobs in 30 seconds

    Every month 400 people find a job with the help of TruckersReport.

  3. Dec 15, 2012 #2
    hatlesstrukr

    hatlesstrukr Light Load Member

    128
    30
    Jan 30, 2010
    El Paso, TX
    0
    The power contacts going into the blower motor are shorting out. You will need to get the motor replaced which is located under the passenger seat. Might be a good time to buy a new filter element usually colored blue.

    *Edit - Just noticed your truck is a 9100i so the blower motor might be located elsewhere. It's usually under the passenger seat in the 9200i/9400i models.
     
    hatlesstrukr, Dec 15, 2012
    hatlesstrukr, Dec 15, 2012
    #2
  4. Dec 15, 2012 #3
    truckinglongisland

    truckinglongisland Bobtail Member

    2
    0
    Dec 15, 2012
    0
    Thanks for the quick response! I looked up blower motors for my make and model and came across a few. Would this be the correct motor? http://www.apairinc.com/dealer/detail.asp?part=BM5052
     
    truckinglongisland, Dec 15, 2012
    truckinglongisland, Dec 15, 2012
    #3
  5. Dec 16, 2012 #4
    hatlesstrukr

    hatlesstrukr Light Load Member

    128
    30
    Jan 30, 2010
    El Paso, TX
    0
    That's the motor all right. If you are doing the work yourself, be careful not to break the plastic cylinder with the fins while taking it off the old motor.
     
    hatlesstrukr, Dec 16, 2012
    hatlesstrukr, Dec 16, 2012
    #4
  7. Sep 14, 2013 #5
    BearDogTrucking

    BearDogTrucking Bobtail Member

    4
    0
    Aug 25, 2011
    Lebanon, Pennsylvania
    0
    I am having a similar problem with my 2001 9400I. Last year my fan quit and I fixed it by putting a new blower motor on. This year I lost all the fan speeds but #4. I put a new motor on today and it still doesn't work on 1,2 or 3. It only works on 4. Any ideas appreciated, thanks!
     
    BearDogTrucking, Sep 14, 2013
    BearDogTrucking, Sep 14, 2013
    #5
  8. Sep 14, 2013 #6
    baha

    baha Road Train Member

    4,137
    2,834
    Jul 25, 2013
    ga
    0
    resistor bad, curly Q 3 wire plug in.
     
    Last edited: Sep 15, 2013
    baha, Sep 14, 2013
    baha, Sep 14, 2013
    #6
  9. Sep 15, 2013 #7
    BearDogTrucking

    BearDogTrucking Bobtail Member

    4
    0
    Aug 25, 2011
    Lebanon, Pennsylvania
    0
    that's what I was thinking but where is the resistor located
     
    BearDogTrucking, Sep 15, 2013
    BearDogTrucking, Sep 15, 2013
    #7
  10. Sep 15, 2013 #8
    QUALITYTRUCK

    QUALITYTRUCK Road Train Member

    1,780
    1,726
    Jun 14, 2009
    romulus,mi
    0
    right next to motor,under seat.(2) screws.30 second job (after seat is removed)
     
    QUALITYTRUCK, Sep 15, 2013
    QUALITYTRUCK, Sep 15, 2013
    #8
  11. Aug 25, 2015 #9
    Bill Grant

    Bill Grant Bobtail Member

    7
    0
    Jul 18, 2015
    0
    I have same prob but only have low speed
     
    Bill Grant, Aug 25, 2015
    Bill Grant, Aug 25, 2015
    #9
  12. Aug 25, 2015 #10
    RustyBolt

    RustyBolt Road Train Member

    2,015
    3,166
    Feb 21, 2015
    Bement, IL
    0
    Pretty common for the resistor to go bad

     
    RustyBolt, Aug 25, 2015
    RustyBolt, Aug 25, 2015
    #10
  • Truckers Report Jobs

    Trucking Jobs in 30 seconds

    Every month 400 people find a job with the help of TruckersReport.

    • Page 1 of 2