Where is everyone #5

Discussion in 'Flatbed Trucking Forum' started by DDlighttruck, Aug 27, 2017.

  1. CAXPT

    CAXPT Road Train Member

    3,121
    14,061
    Feb 10, 2008
    Michigan
    0
    cke and MACK E-6 Thank this.
  2. Truckers Report Jobs

    Trucking Jobs in 30 seconds

    Every month 400 people find a job with the help of TruckersReport.

  3. 50WT

    50WT Road Train Member

    2,252
    19,926
    Dec 26, 2015
    0
    Good looking scooter, I had a 2000 Heritage for a few years. Sold it and bought a ultra classic touring bike because the wife and I traveled a lot by bike back then. I've still got it just don't get to ride as much now. Seeing yours all cleaned up has given me the incentive to wash mine and go for ride today. Be safe.
     
    CAXPT, Feedman, cke and 3 others Thank this.
  4. MACK E-6

    MACK E-6 Moderator Staff Member

    48,765
    225,352
    Sep 19, 2005
    Baltimore, MD
    0
    Yes sir.
     
    CAXPT, cke, dwells40 and 1 other person Thank this.
  5. MACK E-6

    MACK E-6 Moderator Staff Member

    48,765
    225,352
    Sep 19, 2005
    Baltimore, MD
    0
    I’ve been debating swapping it out for a buckhorn, like this.

    A2C36993-2B0D-4B43-A32A-36A7D2A6FE4E.jpeg
     
    CAXPT, cke, AModelCat and 3 others Thank this.
  6. TripleSix

    TripleSix God of Roads

    18,494
    129,533
    Apr 10, 2009
    Copied in Hell
    0
    Debating…

    Are you thinking of running the exact same hand controls as in the pic, or the stock setup? Mirrors?
     
    cke Thanks this.
  7. MACK E-6

    MACK E-6 Moderator Staff Member

    48,765
    225,352
    Sep 19, 2005
    Baltimore, MD
    0
    No, same as stock.

    My mini-ape isn’t really bad, but I’d like just a little bit more pullback.
     
    CAXPT, Feedman and cke Thank this.
  8. 50WT

    50WT Road Train Member

    2,252
    19,926
    Dec 26, 2015
    0
    CAXPT, Feedman, cke and 3 others Thank this.
  9. MACK E-6

    MACK E-6 Moderator Staff Member

    48,765
    225,352
    Sep 19, 2005
    Baltimore, MD
    0
    CAXPT, cke and 50WT Thank this.
  10. AModelCat

    AModelCat Road Train Member

    29,154
    158,535
    Jul 7, 2015
    Canuckistan
    0
    Here's a question for the brilliant minds here on #5. Figure someone here has done some home renos at some point.

    I've got to remove the bottom piece of siding on a house, its cement fibreboard (Hardie Board). This stuff is fairly rigid and does not bend well. Anyone have any experience removing it from the bottom? Everything I see online when looking it up refers to how to remove it when re-siding, nothing about removing it with the intent of reinstalling it later.
     
    CAXPT, Feedman and cke Thank this.
  11. AModelCat

    AModelCat Road Train Member

    29,154
    158,535
    Jul 7, 2015
    Canuckistan
    0
    I took my bike out for a rip last night. It was running a bit off the last little while so I ended up swapping out my coil due to the plug wires deteriorating at the caps. One wire was partially broken. Runs better now. New coil ($300 from Honda) is NLA but I found an aftermarket one on Amazon for under $50. Direct bolt on and the outfit is based out of Quebec. So far I'm impressed. They even sent me a keychain and a coupon for 10% off my next order.
     
    CAXPT, Feedman, cke and 2 others Thank this.
  • Truckers Report Jobs

    Trucking Jobs in 30 seconds

    Every month 400 people find a job with the help of TruckersReport.