Truckers Report Jobs

Find Trucking Jobs

Company Driver Company Driver Dry Van Dry Van Flatbed Flatbed Refrigerated Refrigerated Specialized Specialized Owner Operator Owner Operator
More Trucking Job Searches ⌄ Fewer Trucking Job Searches
⌃

No cruise or jake on 2005 Kenworth W900L w/Cummins ISX

Discussion in 'Trucks [ Eighteen Wheelers ]' started by MARK AT PIMCO TRANS, Aug 21, 2012.

Page 1 of 2
  1. Aug 21, 2012 #1
    MARK AT PIMCO TRANS

    MARK AT PIMCO TRANS Bobtail Member

    19
    9
    Dec 27, 2011
    SAN ANGELO,TX
    0
    Maybe someone can help. Been scratching my head pretty good on this on. Idle can be adjusted from cruise switch, but truck has NO cruise while driving and engine brake acts like it is cutting on and off while operating. Truck has new clutch switch, engine brake wiring harness, engine ECM (replaced for another concearn and yes has cruise enabled - had same concearn before ecm replacement), speedometer head, and transmission speed sensor. Brake pedal switch is working. Truck does not have steering wheel controls just dash switches. Any help is sure appreciated. -Mark
     
    MARK AT PIMCO TRANS, Aug 21, 2012
    MARK AT PIMCO TRANS, Aug 21, 2012
    #1
  2. Truckers Report Jobs

    Trucking Jobs in 30 seconds

    Every month 400 people find a job with the help of TruckersReport.

  3. Aug 21, 2012 #2
    WMGUY

    WMGUY Road Train Member

    1,684
    800
    Jan 1, 2011
    Nine Mile Falls, WA
    0
    i had a similar problem on my 08 volvo with isx, as time went on i wasn't able to bump the idle with cruise switch either but ended up being the switch on the clutch pedal needed adjusted and is a common problem from what the tech said, he said the vibration of the road is enough to kick the switch if not adjusted properly


    if all else is good i wold think it would be the switch
     
    WMGUY, Aug 21, 2012
    WMGUY, Aug 21, 2012
    #2
    MARK AT PIMCO TRANS Thanks this.
  4. Aug 21, 2012 #3
    MARK AT PIMCO TRANS

    MARK AT PIMCO TRANS Bobtail Member

    19
    9
    Dec 27, 2011
    SAN ANGELO,TX
    0
    Clutch switch is new, adjusted properly, and will cut off high idle when depressed. Thanks.
     
    MARK AT PIMCO TRANS, Aug 21, 2012
    MARK AT PIMCO TRANS, Aug 21, 2012
    #3
  5. Aug 21, 2012 #4
    bubbanbrenda

    bubbanbrenda Road Train Member

    1,388
    650
    Feb 27, 2011
    Middletown,Oh.
    0
    If its a ISX there is 2 speed sensors on the trans 1 for speedo and 1 for ECM,or at least my Pete is that way
     
    bubbanbrenda, Aug 21, 2012
    bubbanbrenda, Aug 21, 2012
    #4
  7. Aug 22, 2012 #5
    Worthken

    Worthken Light Load Member

    265
    83
    Jun 2, 2012
    Delmas South Africa
    0
    Have the same issue on my FLB, with S60, with the cruise. Can bump the idling up but the cruise is not working while moving. I read somewhere there is a switch on the tractor parking brake valve, that can cause this. Don't know if its same for KW. Btw the motor still shuts off after 2mins of idling even with the rpm's bumped.
     
    Worthken, Aug 22, 2012
    Worthken, Aug 22, 2012
    #5
  8. Nov 6, 2012 #6
    EccII

    EccII Bobtail Member

    9
    1
    Oct 24, 2012
    0
    still does not work ...
     
    EccII, Nov 6, 2012
    EccII, Nov 6, 2012
    #6
  9. Nov 7, 2012 #7
    bubbanbrenda

    bubbanbrenda Road Train Member

    1,388
    650
    Feb 27, 2011
    Middletown,Oh.
    0
    Did you get it fixed?
     
    bubbanbrenda, Nov 7, 2012
    bubbanbrenda, Nov 7, 2012
    #7
  10. Nov 8, 2012 #8
    MARK AT PIMCO TRANS

    MARK AT PIMCO TRANS Bobtail Member

    19
    9
    Dec 27, 2011
    SAN ANGELO,TX
    0
    Nope still messing with it. Traced and ohmed all wires from speed sensors through body and engine wiring harness. All check out ok. Had local cummins dealer scan truck and it shows no diagnostic codes at all.
     
    MARK AT PIMCO TRANS, Nov 8, 2012
    MARK AT PIMCO TRANS, Nov 8, 2012
    #8
  11. Nov 8, 2012 #9
    allan5oh

    allan5oh Road Train Member

    1,557
    556
    Jan 6, 2010
    Winnipeg, mb
    0
    Check wiring to batteries.
     
    allan5oh, Nov 8, 2012
    allan5oh, Nov 8, 2012
    #9
  12. Nov 8, 2012 #10
    Pablo-UA

    Pablo-UA Road Train Member

    7,604
    1,642
    Oct 11, 2010
    Borispol, Ukraine
    0
    use insite software to read switches status before you do any ajustment
     
    Pablo-UA, Nov 8, 2012
    Pablo-UA, Nov 8, 2012
    #10
  • Truckers Report Jobs

    Trucking Jobs in 30 seconds

    Every month 400 people find a job with the help of TruckersReport.

    • Page 1 of 2