Post flatbed load photos here V2.0

Discussion in 'Flatbed Trucking Forum' started by leftlanetruckin, Feb 18, 2014.

  1. MACK E-6

    MACK E-6 Moderator Staff Member

    48,774
    225,428
    Sep 19, 2005
    Baltimore, MD
    0
    I think I'd rather haul Gunner's load of pipe. :biggrin_2556:
     
    Chewy352 Thanks this.
  2. Truckers Report Jobs

    Trucking Jobs in 30 seconds

    Every month 400 people find a job with the help of TruckersReport.

  3. DDlighttruck

    DDlighttruck Road Train Member

    1,386
    19,919
    Dec 12, 2015
    0
    What's wrong with it? :p
    I had a heavy haul guy laughing at it tonight getting fuel. It actually didn't ride too badly.
     
    Crusader66, passingthru69, SAR and 2 others Thank this.
  4. MJ1657

    MJ1657 Road Train Member

    7,521
    50,151
    Jan 28, 2012
    Isanti, MN
    0
    It was kind of fun right?
     
    Crusader66, johndeere4020, SAR and 3 others Thank this.
  5. DDlighttruck

    DDlighttruck Road Train Member

    1,386
    19,919
    Dec 12, 2015
    0
    The augers are a mess to tie down. The one stack leaned over, luckily towards the middle of the trailer. But yes it's a good challenge. Better than shingles or bricks.

    @Ruthless I had to go for a u-turn on I41 this morning, but picked up a basically brand new Kinedyne 4" strap.
     
  6. MJ1657

    MJ1657 Road Train Member

    7,521
    50,151
    Jan 28, 2012
    Isanti, MN
    0
    Did you pull from both sides on that stack?

    I get some loads from my direct shipper that aren't friendly to pull to one side. I don't have winch track on both sides of my trailer. I start out throwing straps to the opposite side of my winches and tighten them down with portables. Then I throw straps from the opposite side and crank them down hard with my winches.
     
  7. DDlighttruck

    DDlighttruck Road Train Member

    1,386
    19,919
    Dec 12, 2015
    0
    No I didn't. I had a 3" and a 2" on it. The other stack I had 3 2" and it didn't shift. I'll try that though, I like @cnsper idea of a strap with no ends. I was also thinking of @Chewy352 and his moving blankets as strap protectors, too. Fold it to the right size and put it on top, then straps.
     
  8. MJ1657

    MJ1657 Road Train Member

    7,521
    50,151
    Jan 28, 2012
    Isanti, MN
    0
    Flighting or screws as some call them like you hauled are tricky to protect the straps from sharp edges. You have to throw them and tighten the straps then back them off to see where they will lay to know exactly where you will need protection.
     
    Crusader66, johndeere4020, SAR and 3 others Thank this.
  9. DDlighttruck

    DDlighttruck Road Train Member

    1,386
    19,919
    Dec 12, 2015
    0
    That makes sense. I thought either a moving blanket or 4-6 feet of fire hose would work well too.
    IMG_5100.JPG
    What about the larger ones? There are 3 on that skid I think. IMG_5103.JPG
    I took them and shoved them in a bucket at the next stop.
     
  10. MJ1657

    MJ1657 Road Train Member

    7,521
    50,151
    Jan 28, 2012
    Isanti, MN
    0
    Looks like you did ok.

    There is always a way to make it work.
     
  11. Chewy352

    Chewy352 Road Train Member

    1,797
    11,619
    Dec 17, 2013
    Enid, OK
    0
    I need to put my moving blankets back in the truck. I had been using them to cover the carpet while I painted my daughter's room. Mudflaps work well for a lot of stuff too and they're free at most truckstops. The truckstops with tall curbs usually have several laying around. I've even found several at shippers with big potholes.
     
  • Truckers Report Jobs

    Trucking Jobs in 30 seconds

    Every month 400 people find a job with the help of TruckersReport.