You need to learn how to use them properly on dry pavement before applying them on slippery surfaces, but they can be used if used properly. Check out the thread that @NorthernMechanic posted.
Probably a stupid rookie question.
Discussion in 'Questions From New Drivers' started by Alhb54, Sep 23, 2017.
Page 3 of 5
-
KeepitMovin47, Shock Therapy and Ctalarico07 Thank this.
-
Trucking Jobs in 30 seconds
Every month 400 people find a job with the help of TruckersReport.
-
These cdls schools don't teach you anything but how to pass the test to get your cdls. The real learning begins on your own
KeepitMovin47 Thanks this. -
Zeviander Thanks this.
-
Make sure in slick conditions you do any (firm braking) while travelling straight this means you may need to slow extra before curves so as not to reach to high a speed while making the curve never (hard brake)
KeepitMovin47 and Lepton1 Thank this. -
It's your truck and nobody knows it better. The advice given here is good on the most part. Feel the truck and know it's capabilities before you put it to the test going down a grade. I've hauled loads over 105,000lbs with no engine brake whatsoever. Going down I84 in Utah was long but did not ever smoke the brakes and had plenty of brake to make an emergency stop if needed. The trick is in the speed the truck is traveling down the hill. If you're going to fast you're asking for trouble. As a general rule I'd go down 35mph with the engine brake and 25mph without one. If you're loaded lighter then I would adjust the speed. You can adjust your speed when you know the truck. I don't know if you've ever been out west but there's some pretty good grades. I would haul gasoline in a super tanker and gross around 110,000lbs. Go down NV163 into Laughlin NV when it was just two lanes. That will convince going slow is better than fast. I'd see those truck going 55mph down that hill and pass them at the bottom of the grade when they had to pull over because of brake smoke. So like I said, you know your truck and do the testing on a safe road.
Lepton1 Thanks this. -
Anyway, last winter I was driving for about 3 weeks in WA and OR. The freeways were nice and dry, so then I decided to take a short cut over some mountain. Couple miles away from the freeway nothing but snow and ice, no place to turn around, so I kept going up the hill, and barely made it to the top, there I stopped to ##### the situation, should I wait till summer, or risk to slide down hill. I decided to keep going really slowly, 10 to 20 mil., the retarder OFF.
When I came to my first turn, I started braking very softly, but the steering wheels blocked and I went straight, luckily I was very slow and nothing happened. But I was thinking what if I get to bigger curve or slope how do I brake without locking the steering wheels. OK I will try the retarder, I did and from then on nice smooth braking, not the slightest problem for about 15 miles all the way down to the valley.
Since then, I always use it, nothing slows the truck smoother than combination retarder and gas pedal.
I think if I should get into trouble then I was too fast anyway and in that case nothing helps me.Lepton1 Thanks this. -
-
KeepitMovin47 Thanks this.
-
Going uphill if you start going straight in a curve ease off on the throttle to get it to turn, then get back on the throttle to maintain momentum. Again, this is pumping the throttle with small changes in in horsepower, larger as needed. This is most common when you are plowing through mud with your differentials locked. -
But with jake brake, I like to use it. It's much smoother braking and you never loose the steering capabilities.
Also once the steering wheels lock it takes little bit time till they start rolling again, and that fraction of a second in those situations always seem to me to last an eternity.
And also didn't had any room to slide around.Lepton1 Thanks this.
Trucking Jobs in 30 seconds
Every month 400 people find a job with the help of TruckersReport.
Page 3 of 5