Truckers Report Jobs

Find Trucking Jobs

Company Driver Company Driver Dry Van Dry Van Flatbed Flatbed Refrigerated Refrigerated Specialized Specialized Owner Operator Owner Operator
More Trucking Job Searches ⌄ Fewer Trucking Job Searches
⌃

6nz ecm on bxs?

Discussion in 'Trucks [ Eighteen Wheelers ]' started by scarecrow454, Jan 14, 2009.

Page 2 of 4
  1. Jan 17, 2009 #11
    scarecrow454

    scarecrow454 Bobtail Member

    10
    0
    Jan 14, 2009
    Ky
    0
    Can you tell me a specific regulator you recommend?
     
    scarecrow454, Jan 17, 2009
    scarecrow454, Jan 17, 2009
    #11
  2. Truckers Report Jobs

    Trucking Jobs in 30 seconds

    Every month 400 people find a job with the help of TruckersReport.

  3. Jan 18, 2009 #12
    V8Lenny

    V8Lenny Road Train Member

    1,016
    130
    Aug 3, 2008
    Europe
    0
    Yes you can if you are skilled enough in programming.
     
    V8Lenny, Jan 18, 2009
    V8Lenny, Jan 18, 2009
    #12
  4. Jan 18, 2009 #13
    scarecrow454

    scarecrow454 Bobtail Member

    10
    0
    Jan 14, 2009
    Ky
    0
    I have another dumb question. Can my 6nz ecm be flashed to the 7cz program?
     
    scarecrow454, Jan 18, 2009
    scarecrow454, Jan 18, 2009
    #13
  5. Jan 18, 2009 #14
    C16KIWI

    C16KIWI Medium Load Member

    575
    142
    Jun 14, 2008
    New Zealand
    0


    Yes:biggrin_255::biggrin_255:
     
    C16KIWI, Jan 18, 2009
    C16KIWI, Jan 18, 2009
    #14
  7. Jan 18, 2009 #15
    Mr. Haney

    Mr. Haney Road Train Member

    2,693
    2,040
    Dec 17, 2008
    0
    The ones made by Parker seem to work very well.
     
    Mr. Haney, Jan 18, 2009
    Mr. Haney, Jan 18, 2009
    #15
  8. Jan 18, 2009 #16
    scarecrow454

    scarecrow454 Bobtail Member

    10
    0
    Jan 14, 2009
    Ky
    0
    good deal! thanks!!
     
    scarecrow454, Jan 18, 2009
    scarecrow454, Jan 18, 2009
    #16
  9. Jan 18, 2009 #17
    550hpW900L

    550hpW900L Road Train Member

    1,874
    1,090
    Jan 29, 2008
    norcal
    0
    I had a regulator on mine. Sometimes it worked sometimes it didnt. It derated with the regulator lots of times, i pulled it off and it seems to have quit.
     
    550hpW900L, Jan 18, 2009
    550hpW900L, Jan 18, 2009
    #17
  10. Jan 19, 2009 #18
    V8Lenny

    V8Lenny Road Train Member

    1,016
    130
    Aug 3, 2008
    Europe
    0
    Here it is, again.

    The circuit consists of two diodes and a 1 kilo-ohm pot. Its sensitivity can be adjusted by rotating the pot - this should be set so that the circuit clips at as high a manifold pressure as possible.
    [​IMG]
     
    V8Lenny, Jan 19, 2009
    V8Lenny, Jan 19, 2009
    #18
    Mr. Haney and underpsi Thank this.
  11. Jan 19, 2009 #19
    scarecrow454

    scarecrow454 Bobtail Member

    10
    0
    Jan 14, 2009
    Ky
    0
    When I get the ecm on, I'll play around with it and see what works the best. Thanks for the info!
     
    scarecrow454, Jan 19, 2009
    scarecrow454, Jan 19, 2009
    #19
  12. Jan 20, 2009 #20
    Mr. Haney

    Mr. Haney Road Train Member

    2,693
    2,040
    Dec 17, 2008
    0
    I've never worked with this set up or even heard of it before. I have a question. Will it allow the ECM to see the range of manifold pressure as it rises and falls, but just cancels the signal out at the higher setting of your choice? Not send a preset signal all the time to the ECM.
     
    Mr. Haney, Jan 20, 2009
    Mr. Haney, Jan 20, 2009
    #20
  • Truckers Report Jobs

    Trucking Jobs in 30 seconds

    Every month 400 people find a job with the help of TruckersReport.

    • Page 2 of 4