Tips for new drivers (things to do)
Discussion in 'Experienced Truckers' Advice' started by notarps4me, Feb 21, 2009.
Page 5 of 9
-
-
Trucking Jobs in 30 seconds
Every month 400 people find a job with the help of TruckersReport.
-
I can't take the credit for it. That came from the guy who road tested me at PAM.jasondt2001 said: ↑Also - give it a little fuel, between 1100 and 1500 rpm is where ours likes to shift depending on your speed.... keep steady pressure on the gear shift and it'll 'float' into place. This is how we are being taught to downshift using no clutch.
It sounds easy, but, i'm STILL getting the hang of it...
Scarecrow - that's one hell of a hint! I love it! Thank you!!!!!Click to expand... -
jasondt2001 said: ↑Yes but they want me to use the clutch...that why its so hard to do...i guess i will get it eventually...dr5169 said: ↑Also - give it a little fuel, between 1100 and 1500 rpm is where ours likes to shift depending on your speed.... keep steady pressure on the gear shift and it'll 'float' into place. This is how we are being taught to downshift using no clutch.
It sounds easy, but, i'm STILL getting the hang of it...
Scarecrow - that's one hell of a hint! I love it! Thank you!!!!!Click to expand...Click to expand... -
the biggest difference that i have found when it come to using the clutch is that you gotta be a fair bit faster at shifting. other than that, practice makes perfect.
-
Another tip is round abouts. Be careful with these. Many are in smaller towns and they are hard to negotiate. They can be a bear to get into on account of traffic. Many are narrow and there are lot's of 4 wheelers. Some of them I have my driver side steer up against the curb and my spread is about to curb the passenger side curb when I exit. Another bad part is that there can be anywhere from a half dozen to a dozen exits. If you get confused don't exit and get on the wrong road. If you have to make a dozen laps or two around this unforgiving truck obstacle till you figure out where to exit...

Remember the chevy chase movie? One of the vacation ones where they spend a day or so driving in circles...
When I enter one of these my GPS says enter round about and take the 9th exit..... some of these exits are so close together it is hard to tell which one you need. Watch for 4 wheelers in these. I know there must be a sign for them before they enter the round about. Attention 4 wheelers State law requires you to get stupid in this circle...
Last edited: Feb 28, 2009
panhandlepat Thanks this. -
Look! Big Ben, Parliament...
-
Keep your mirrors clean and act like a professional . Oh yeah try to shower at least every other day.
-
I wouldn't put too much stock in the idea of a gear every tem miles per hour. If you have a taller or shorter rear end, that will change.
Point is, any truck you drive, you should mentally familiarize yourself with the spread and feel. One thing I've always done is first to check the play in the stick, so I know how much slop I'm dealing with.
After driving about ten different tranny's, it starts getting easy to become grindlessly proficient in only a run or two thru the gears.
Just stop telling yourself it's hard, and feel it out, remember what you felt, and relax.
Mostly relax. Rushing a gear is usually a grinder, cruncher, or the deadly bang. -
I've found there are a couple other uses for washer fluid.......
1. When it's really cold out and there is snow on the 5th wheel, carefully clean off the snow and splash some washer fluid around the "fingers". Living here in New England, I have experienced many times the 5th wheel not locking.
2. I have only tried this once, and only once, I was backing into a dock in Allenstown PA, loaded with water. It had been raining during the day and then during the evening it froze. I could just touch the dock's rubber bumpers but couldn't get a good "squish" on them. I didn't have salt or cat litter. I tried some washer fluid. It worked. I was able to dock the truck. When I was unloaded, I had to backup a little to get the dock lock to release, I had slid while the forklift was unloading.
I am not sure if the second one would work again, I'll have to do some more testing, the first one has worked without fail for the last 7 years. -
Don't waste time but never rush.
Allow extra time, Murphy is out there.
Know where you're going. The shipper or consignee will usually give you good directions as well as let you know if you can park there the night before.
Never be afraid to ask for help. If approached the right way most people are more than happy to help you out.Ron M and panhandlepat Thank this.
Trucking Jobs in 30 seconds
Every month 400 people find a job with the help of TruckersReport.
Page 5 of 9
Related Categories
-
Any recommendations on coming...
67Arch posted Jan 6, 2026 at 11:27 PM -
Stranded for almost 3 weeks
956Trucker posted Jan 5, 2026 at 6:44 PM -
FLD 120 sunscreen exact fit
Dino soar posted Jan 5, 2026 at 9:55 AM -
What happens if they find a gun?
FloridaRetired posted Jan 4, 2026 at 8:34 PM -
Lumper Fees?
Rayj00 posted Jan 4, 2026 at 9:01 AM -
Goodbye to a horrible '25
rbrtwbstr posted Jan 2, 2026 at 8:55 AM -
Help! Trouble transferring NJ...
Jay856 posted Jan 1, 2026 -
Those who run gliders.....
nikmirbre posted Dec 31, 2025 -
HAPPY NEW YEAR
Wargames posted Dec 30, 2025 -
Any recommendations for someone...
jimbo33 posted Dec 29, 2025
Loading...
Recent Threads
-
Private Equity Firm Acquires Dart
BrothaTrucka513 posted Jan 8, 2026 at 6:51 PM -
Research Questions
truckingresearch101 posted Jan 8, 2026 at 5:12 PM -
Oklahoma Senator files bill...
drvrtech77 posted Jan 8, 2026 at 2:14 PM -
That’s gonna hurt…
drvrtech77 posted Jan 8, 2026 at 11:23 AM -
CAT 3406E – Where exactly is...
RJCR713 posted Jan 7, 2026 at 10:22 PM -
Oversize without permits,...
eggo posted Jan 7, 2026 at 8:14 PM -
Need Help Locating Engine...
RJCR713 posted Jan 7, 2026 at 7:29 PM -
Landstar has officially gave...
drvrtech77 posted Jan 7, 2026 at 3:53 PM -
Uh oh, New CDL holder with a...
WrJoe posted Jan 7, 2026 at 2:56 PM -
Big Wind, Big Mess
Opus posted Jan 7, 2026 at 9:51 AM
Loading...