Starting in 3rd

Discussion in 'Experienced Truckers' Advice' started by doglover44, Jan 20, 2015.

  1. doglover44

    doglover44 Light Load Member

    191
    28
    Apr 30, 2008
    Ohio
    0
    I was driving today and I started in 3rd gear is it bad to start that late should I have started in 1st or 2nd ?
     
  2. Truckers Report Jobs

    Trucking Jobs in 30 seconds

    Every month 400 people find a job with the help of TruckersReport.

  3. EZ Money

    EZ Money Road Train Member

    No need to start in first gear unless really heavy or on a hill.
    Depends on the truck,load and transmission.

    I usually start off in 4th on flat ground unless i'm really heavy.
     
    Speedemon1084, pattyj and carl320 Thank this.
  4. heavyhaulerss

    heavyhaulerss Road Train Member

    3,723
    2,040
    Dec 23, 2009
    AL/TN BORDER
    0
    3rd when empty. 1st or 2nd when loaded.
     
    pattyj and Skate-Board Thank this.
  5. Woodys

    Woodys Heavy Load Member

    774
    1,629
    Mar 16, 2010
    Tampa, FL
    0
    No idea if it actually hurts the tranny, as I always drive company trucks. However I usually start in 4th if my trailer is under 10k. I rarely, if ever use 2nd unless I have a heavy load that needs it (obviously). Having said that, I drive local and my state is super duper flat so I don't have to worry about hills at all.

    Everyone I know uses 4th when empty. Like I said though, not sure at all if it hurts the tranny in any way.
     
  6. EZ Money

    EZ Money Road Train Member

    As long as you are not slipping the clutch or the cab is bouncing up and down I doubt it will hurt a thing.
    Every truck is different. I have driven a few that needed a second or third gear start.
     
    Hammer166 Thanks this.
  7. damutt

    damutt Road Train Member

    1,126
    370
    May 6, 2013
    0
    i always start in 3rd gear. unless as stated stupid heavy or on a steep upgrade were i had to stop
     
  8. scottied67

    scottied67 Road Train Member

    10,826
    12,673
    Mar 14, 2010
    california norte
    0
    I'm so leery of burning up the clutch I start in LO even when bobtail
     
  9. Broccelli

    Broccelli Medium Load Member

    373
    198
    Jan 2, 2014
    Virginia
    0
    Sarcasm?


    I usually start in 1st or 2nd when loaded (depending on weight) and I'll start in 2nd when mt. But I haul reefers so they are a tad heavier than a dry box. You can start the truck in whatever gear you want just keep in mind the longer you have to ease that clutch out the more you are burning it up.

    I am usually conservative with the gear I start out in but like Scottie I don't feel like dropping some hard earned money on a clutch any sooner than neccessary. I don't go as far as starting in LO though (still unsure if that was sarcasm or not).
     
    scottied67, gpsman and snowwy Thank this.
  10. G.Anthony

    G.Anthony Road Train Member

    4,564
    5,952
    Dec 10, 2014
    0
    For all these years, I have started off in 2nd gear, loaded or empty. On a hill, 1st, very heavy loads, 1st.

    When bob-tailing, maybe 3rd, maybe 4th, but most times, 3rd. Whenever I'd have an automated shift? Drive, Whether it be loaded, empty, or bob-tailing
     
  11. TNMT

    TNMT Light Load Member

    226
    229
    Nov 11, 2008
    Front of keyboard
    0
    Start in the highest gear you can. 3rd is OK in most trucks empty. If you have to slip the clutch to move you're too high, If you can let out the clutch and the truck moves with light pressure on the pedal you're OK.
     
    Lepton1 Thanks this.
  • Truckers Report Jobs

    Trucking Jobs in 30 seconds

    Every month 400 people find a job with the help of TruckersReport.